Haier 1U09ES2VHA, Руководство по обслуживанию

Страница: 21 / 76

REMOTE CONTROL FUNCTIONS
PAGE 21
ENGLISH
to adjust left and right direction referring to the figure below.
'
Cautions:
• Turn the unit off prior to opening the horizontal louver and
adjusting the vertical blades by hand.
• When humidity levels are high, condensate water may oc -
cur at the air outlet if all vertical louvers are adjusted to left
or right.
• It is advisable not to keep the horizontal louver in the
downward position for an extended period of time in COOL
or DRY mode, otherwise condensate water may form on
the louver.
Note:
When turning the unit on, the remote control will automatically
return the louver to the previous set swing position. When turn
-
ing the unit off, the louver will rotate to the full open position
prior to closing .
10 Timer Button
On-Off Operation
1. Start the unit and select the desired operating mode.
2. Press the TIMER
7,0(5
button to change to TIMER mode.
Every time the TIMER button is pressed, the display changes
as follows:
Remote control display:
BLANK
TIMER ON TIMER OFF TIMER ON-OFF TIMER OFF-ON
0.5h 0.5h 0.5h 0.5h
Select the desired TIMER mode (TIMER ON or TIMER OFF or
TIMER ON-OFF). The “ON” or “OFF” icon will flash.
3. Press the / buttons to set the time.
- Pressing this button increases the time in 0.5 hour
increments between hours 0 and 12, and 1 hour increments
for times between hours 12 and 24.
- Pressing this button decreases the time in 0.5 hour
increments between hours 0 and 12, and 1 hour increments
for times between hours 12 and 24.
The on or off time can be adjusted up to 24 hours.
4. Confirm timer setting
After adjusting the time, press the CONFIRM/CANCEL
&21),50
&$1&(/
button and confirm the time ON or OFF icon stops flashing
and remains displayed.
5. Cancel timer setting
Press the TIMER
7,0(5
button repeatedly until the time display
clears.
Note:
Holding the
/ button down will rapidly cycle the
time. After replacing batteries or a power failure occurs, the
time setting will need to be reset.
According to the Time setting sequence of TIMER ON or
TIMER OFF, either Start-Stop or Stop-Start can be achieved.
12 EXTRA FUNCTION Button
Function:
A) Fan Mode -
Is indicated by the icon. Only the fan will
operate in this mode. See section 8 “FAN Button” for
changing the fan settings.
B) Intelligent upward airflow, C) Intelligent downward airflow,
D) Reset intelligent airflow position
1. Press the ON/OFF button on the remote control to turn
the unit on.
Select the desired operating mode.
2. Setting the intelligent airflow function
Press the EXTRA FUNCTION
(;75$
)81&7,21
button to enter ad-
ditional options. Press this button repeatedly to access
the louver settings. The louver icon will cycle through the
following three settings.
Healthy
airflow
upward
Healthy
airflow
downward
Present
position
Select the desired position, then press the CONFIRM/
CANCEL
&21),50
&$1&(/
button to set the function.
3. Canceling the intelligent airflow function
Press the EXTRA FUNCTION
(;75$
)81&7,21
button to enter addi-
tional options. Press this button repeatedly to access the
louver settings. Cycle the button to the louver icon “pres
-
ent” position, then press the CONFIRM/CANCEL
&21),50
&$1&(/
button to cancel the function.
Notice: Do not reposition the horizontal louver by hand.
This may cause the louver to run incorrectly and not
match the icon displayed on the remote control. If the
louver is not running correctly, turn the unit off for one
minute, then back on, and adjust the louver setting with
the remote control.
Note:
1. After setting the intelligent airflow function, the louver
position is fixed.
2. In cooling, it is better to select the
mode.
3. In heating, it is better to select the mode.
4. In cooling and dry modes, using the air conditioner for a
long period of time under high humidity conditions, con
-
densate water may form on the grille/louver.
E) Right and left airflow setting
This will adjust the left and right airflow of the unit. Press