background image

Interfacing to the KE-USB36 Input Header

The KE-USB36 features a 2x20 header for interface to your input 
devices. The input header is arranged with grounds on the end 
pins of the header, and the 36 inputs between them. The board 
is  labeled  near  each  header  pin,  designating  the  input  number 
that the pin represents. Each of the pins may be programmed to 
emulate any key on a standard PC keyboard as well as the Left, 
Middle, and Right mouse buttons.

Inputs  on  the  KE-USB36  header  are  activated  by  shorting  them 
to  one  of  the 
provided  logic 
grounds on the 
header.  When 
activated,  the 
input  will  report  the  keystroke  that  it  has  been  programmed  to 
emulate. If held active, the keystroke will repeat (if programmed 
to  repeat),  based  on  the  repeat  rates  and  delays  set  within  the 
operating system.

The inputs are intended to handle mechanical switch inputs and 
are debounced for that purpose. Logic drivers may be attached 
to the inputs as well, provided they are an active low, logic level 
signal. Refer to the Appendix A on specifications for the timing of 
logic signals.  Never attach any external power to the Inputs.

The  KE-USB36  input  header  is  a  dual  row  header  with  .100” 
spaced  pins.  This  format  is  suitable  for  many  readily  available 
connectors on the market, including a typical IDE hard drive cable. 
Since all the inputs require the same logic ground reference, you 
may  “daisy  chain”  the  ground  to  all  of  your  switches.  We  also 
offer a breakout board (our part number IOX36) for interface to 
the  KE-USB36.  This  interface  board  attaches  to  the  KE-USB36 
header  through  an  IDE  cable  (provided  with  the  IOX36).      See 
the  accessories  page  of  this  manual  for  details  on  the  IOX36. 
Appendix B demonstrates  connection techniques for switches on

Figure 4

 - The KE-USB36 Input Header

a  Trackball.  Use  the  controls  for  either  the  X  or  Y  axis  for  the 
Spinner, according to the axis on which the Spinner movement is 
to appear.

In  order  to  accommodate  the  various  brands  of  Trackballs,  the 
KE-USB36 provides check boxes to reverse the Left-Right and Up-
Down  movements  of  the  Trackball.  If  you  find  that  one  or  both 
directions of your cursor movement from the Trackball are reversed, 
check the appropriate box in the configuration program.

The  KE-USB36  uses  the  standard  USB  keyboard  buffer  length 
which allows for up to six keys being reported “ON” at the same 
time.    This  limitation  only  pertains  to  KE-USB36  inputs  that  are 
programmed with the repeat selection enabled.  Use of the Left and 
Right Shift, Left and Right Alt, Left and Right Control, and Windows 
GUI keys, can be used in addition to the six key limitation.

The KE-USB36 has the option of repeating an input that is held 
on. If the input is selected to repeat, that input will count toward 
the six key limit. Keys that are set to not produce a repeat will not 
be  subject  to  the  6  key  limitation,  provided  there  are  no  more 
than 5 repeated keys currently active. Note that inputs defined as 
mouse buttons do not figure into the six key limit.  

Inputs on the KE-USB36 which emulate a multiple key sequence, 
such as Shift+F1, will automatically have repeat disabled.

Appendix C:
KE-USB36 Read/Write from the Command Line

In addition to the KEUSB36.EXE configuration program, the CD 
supplied with the KE-USB36 contains two command line programs 
for reading from and writing to the KE-USB36 device. For details, 
see the README.TXT file included on the CD.

15

6

Содержание KE-USB36





















Отзывы: