Haes AOV Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

Haes AOV Series Скачать руководство пользователя страница 29

AOV Installation, Commissioning & Operating Manual

Approved Document Ref: UI-AOV-01 Issue 7.0

27

SETUP & PROGRAMMING

Use button 1 to scroll to the attribute that requires editing, inidicated by a pulsing LED as per table below.

Use button 2 to switch the attribute ON or OFF

Then use button 1 to move to the next attribute if required.

Press the ENTER button to return back to the circuit selection, indicated by a steady circuit LED.

( ) =

Default State

3121 Input Circuit Function Settings

Attributes

Input Circuit

Detector Circuit

Rain Circuit

PIR Circuit

LED Status

Fast

Pulse

Slow

Pulse

Fast

Pulse

Slow

Pulse

Fast

Pulse

Slow

Pulse

Fast

Pulse

Slow

Pulse

CIRCUIT LATCH

(Gen Alarm LED)

Latching

Non

Latching

Latching

Non

Latching

Latching

Non

Latching

Latching

Non

Latching

SHORT CIRCUIT

(Gen Fault LED)

Short cct

= alarm

Short cct

= fault

Short cct

= alarm

Short cct

= fault

Short cct

= alarm

Short cct

= fault

Short cct

= alarm

Short cct

= fault

DETECTOR REMOVAL

(Gen Disable LED)

Detector

Removal

On

Detector

Removal

Off

4

1

4

1

Thermostat Controlled Ventilation Mode

This option allows for thermostat control of vent opening by using a thermostat to switch in a 4K7
resistance between the VENT CONT OP and COM terminals. This will allow the vent to open a set
distance – either 10%, 20% or 50% of full opening – when the pre-set temperature on the thermostat is

reached.

Enter the above code and press ENTER button.

The Vent Open Red LED will be rapidly pulsing. Press ENTER button to set the required amount of Vent
opening as indicated by the Input and Detector Yellow Fault LED’s on the display as shown.

Both Input and Detector LED’s OFF = Default setting. This function is not selected i.e normal operation
of the VENT CONT switch.

Input LED ON = 10% of full opening.

Detector LED ON = 20% of full opening.

Both Input and Detector LED’s ON = 50% of full opening.

Successive pressing of ENTER button will cycle through the above settings until the returning to the
original state (both Input and Detector LED’s OFF = normal operation).

When the required Vent opening setting is indicted press button 1 and hold for appox. 3 second to return
to Main Display.

*

*

*

*

*

*

*

*

*

CIRCUIT TO BE EDITED

- LED status when

NOT

in Edit Mode

- Fast Pulse Status indicated by ‘STEADY’ LED

- Slow Pulse Status indicated by LED ‘OFF’

«
...
27
28
29
30
31
...
»

Содержание AOV Series





































Отзывы:

Нет отзывов