manualshive.com logo in svg

Haes AOV Series, Инструкция по установке, пусконаладке и эксплуатации, Страница: 17 / 36

Поделиться
Скачать
Haes AOV Series Скачать руководство пользователя страница 17

AOV Installation, Commissioning & Operating Manual

Approved Document Ref: UI-AOV-01 Issue 7.0

15

PANEL FUNCTIONS

CABLE TYPES & LIMITATIONS

CABLING

CABLE LENGTHS

MAINS PROVISION

To  comply  with  EMC  (Electro  Magnetic  Compatibility)  regulations  and  to  reduce  the  risk  of  electrical 

interference in the system wiring, we recommend the use of screened cables throughout the installation.
Acceptable, commonly available, screened cables, which can be used on both the sounder and detector 

circuits include, NoBurn™ FP200™, Firetuff™, Firecel™, MICC (Pyro™) or any other cable complying with 
BS 6387 categories C, W, Z.. Refer to BS 5839 pt1  clause 26 for detailed information on cables wiring 

and interconnections.

Suitable cables should be brought into the cabinet using the knockouts provided via a suitable cable gland 
recommended for use with that cable. The screen or drain wire of circuits should be bonded to earth at 
one location only, and should be continuous throughout the circuit. Drain wires should be terminated in the 
cabinet using the earthing terminal provided.

The maximum recommended cable length for a zone or sounder circuit is 1Km. This, however, is highly 

dependant on the number and type of devices connected.

If in doubt, cable load and resistance calculations should be undetaken to ensure devices are working 

within specified limits.

The mains supply to the control panel should be hard wired, using suitable three  core cable (no less 
than 1.0 mm² and no more than 2.5mm²) or a suitable three conductor system that meets the appropriate 
national wiring regulations. The panel should be fed from an isolating switched fused spur, supplied directly 

from the Main Distribution Board, fused at 3A. This should be secure from unauthorised operation.

As an alternative to a switched fused spur, an appropriately fused double pole isolating device may be 
used providing it meets the appropriate national wiring regulations.

B -

Connections for 24v VRLA batteries

VENT CONT

Vent control inputs for manual operation of vents via seperate 3 way control switch.

OP

Open vent

COM

Common 0v reference for switching inputs

CL

Close vent

OP

COM

CL

Open Vent

Close Vent

Содержание AOV Series





































Отзывы:

Нет отзывов