Haes AOV Series Скачать руководство пользователя | Manualshive

Страница: 2 / 36

background image

IMPORTANT NOTE

PLEASE READ THIS MANUAL BEFORE HANDLING THE EQUIPMENT AND

OBSERVE ALL ADVICE GIVEN IN IT

THIS PARTICULARLY APPLIES TO THE PRECAUTIONS NECESSARY TO AVOID

E.S.D

The panel is safe to operate provided it has been installed in compliance with the manufacturer’s instructions
and used in accordance with this manual.

Hazardous voltages are present inside the panel—DO NOT open it unless you are qualified and authorised

to do so. There is no need to open the panel’s enclosure except to carry out commissioning, maintenance
and remedial work. This work must only be carried out by competent service personnel who are fully
conversant with the contents of the panel’s installation manual and have the necessary skills for maintaining
this equipment.

Disclaimer

No responsibility can be accepted by the manufacturer or distributors of this control panel for any
misinterpretation of an instruction or guidance note or for the compliance of the system as a whole. The
manufacturer’s policy is one of continuous improvement and we reserve the right to make changes to

product specifications at our discretion and without prior notice. E & O E.

IMPORTANT SAFETY NOTES

Haes Systems Ltd, Unit 3 Horton Industrial Park, UB7 8JD

15

Model Number

3 Amp, Automatically Opening Vent control panel, AOV-3 (standard spec) & AOV-3H (high spec)

5 Amp, Automatically Opening Vent control panel, AOV-5 (standard spec) & AOV-5H (high spec)

10 Amp, Automatically Opening Vent control panel, AOV-10 (standard spec) & AOV-10H (high spec)

In accordance with the following directives:

2006/95/EC - The Low Voltage Directive

2004/108/EC - The Electromagnetic Compatibility Directive

Is in conformity with the applicable requirements of the following documents:

BSEN 50130-4 +A1, 2014. Product family standard immunity requirements for components of fire, intruder and social alarm

systems.

BSEN 61000-6-3, 2011. Electromagnetic Compatibility (EMC) General Standards. Emission standard for residential,

commercial & light industrial environments.

BSEN 62368-1, 2014. Audio/video information and communication technology equipment safety requirements.

ATTENTION

«
1
2
3
4
...
»

Содержание AOV Series





































Отзывы:

Нет отзывов

Похожие инструкции для AOV Series

Бренд: Valor Страницы: 20

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Lamtec Страницы: 22

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

Бренд: Eaton Страницы: 96

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: DSE Страницы: 2

UNDER CONTROL CP-30A PILOT

Бренд: G-Force Страницы: 2

Бренд: Coris Страницы: 4

MS6-SV-...-D-10V24

Бренд: Festool Страницы: 32

Бренд: SOMFY Страницы: 56

Бренд: Inkel Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды