Hachette Agora Bismarck Pack 04 Скачать руководство пользователя страница 8

Страница: 8 / 40

Taking care that the parts do not fly off, cut part

and three parts

from the frame

34-05

. Glue them

to the top of the control centre

34-01

Cut four parts

and one part

from the frame.

Glue them around the edge of the control centre

34-01

as shown.

Cut part

from the frame and glue it in place on the

roof of the radar unit as shown.

Check the fit of the radar unit

34-02

to the base of the

radar unit

34-03

and check that the screw fitted

earlier (see page 7 step 2) is fully tightened. Glue the
radar unit in place.

Completed work

The radar control centre and turntable
have been assembled and fitted with
accessories. The engine and gearbox
for the radar were fitted and two
ladders were attached to the front
superstructure. Frames

34-07

and

34-08

and two

2 x 5 mm screws will

be used in the next stage.

34-01

34-02

34-03

34-07

34-08

AGORA

MODELS

AGORA

MODELS

Содержание Agora Bismarck Pack 04









































Результаты поиска

Содержание Agora Bismarck Pack 04

Отзывы:

Похожие инструкции для Agora Bismarck Pack 04

Бренды по названию

Популярные бренды

Hachette Agora Bismarck Pack 04, Инструкции по сборке

Результаты поиска

Содержание Agora Bismarck Pack 04

Отзывы:

Похожие инструкции для Agora Bismarck Pack 04

Бренды по названию

Популярные бренды