Hachette Agora Bismarck Pack 04 Скачать руководство пользователя страница 38

Страница: 38 / 40

Glue the two sections of the conning tower together
so that the pegs on part

44-05

fit into the sockets on

part

44-04

, as shown.

Check the fit of assembly

44-04/44-05

in the opening

of the upper mast deck

44-01

, noting the orientation,

shown here. Apply a little superglue to the tabs on the
lower edge of parts

44-04/44-05

and glue in place.

Take frame

44-06

, which will form the ammunition hoist

for the 2-cm magazines. Cut parts

and

from the

frame, taking care they do not fly off. Note that parts

and

are similar, but part

is smaller than part

Slot the central upright ‘spine’ of part

through the

central opening in part

and slide part

down as far

as it will go. Note that part

is slightly tilted, as

shown. Fix in place with a tiny drop of superglue.

Cut part

from the frame and fit it across the top of

the central spine of part

, positioning the notches

(circled) as shown. Again, part

is slightly tilted, at the

same angle as part

, as shown. Fix in place with a

tiny drop of superglue.

Take the first part

and fit the end with a loop

through the opening in part

. Then fit the loop onto

the horizontal peg of part

. Apply a drop of glue to

hold the loop in place (arrow).

44-01

44-05

44-04

44-06

AGORA

MODELS

AGORA

MODELS

Содержание Agora Bismarck Pack 04









































Результаты поиска

Содержание Agora Bismarck Pack 04

Отзывы:

Похожие инструкции для Agora Bismarck Pack 04

Бренды по названию

Популярные бренды

Hachette Agora Bismarck Pack 04, Инструкции по сборке

Результаты поиска

Содержание Agora Bismarck Pack 04

Отзывы:

Похожие инструкции для Agora Bismarck Pack 04

Бренды по названию

Популярные бренды