Hachette Agora Bismarck Pack 04 Скачать руководство пользователя страница 16

Страница: 16 / 40

. THE RADAR UNIT

Fix the deck

37-07

in place on the top of part

37-04

Put the foretop command post attachment

37-04

your work surface. Take the deck

37-07

and check the

fit on the top of part

37-04

. Apply superglue to the

underside of the deck

37-07.

Turn part

37-04

over. Take the cog

37-08

and one of

the shafts

37-11

. Fit the shaft into the cog

37-08

then pass the cog through the hole in part

37-04

Identify the fixing point (circled) for the next cog

37-09

and shaft

37-11

Fit the shaft

37-11

through the cog

37-09

and into the

fixing point in part

37-04

. When correctly fitted, the

smaller ring of teeth on the cog

37-09

will engage

with the teeth on the outer edge of cog

37-08

Fit cog

37-10

on the first shaft

37-11

so that its teeth

engage with the outer ring of teeth on cog

37-09

37-07

37-04

37-07

37-11

37-08

37-04

37-10

37-04

37-09

37-11

37-04

37-09

37-08

AGORA

MODELS

AGORA

MODELS

Содержание Agora Bismarck Pack 04









































Результаты поиска

Содержание Agora Bismarck Pack 04

Отзывы:

Похожие инструкции для Agora Bismarck Pack 04

Бренды по названию

Популярные бренды

Hachette Agora Bismarck Pack 04, Инструкции по сборке

Результаты поиска

Содержание Agora Bismarck Pack 04

Отзывы:

Похожие инструкции для Agora Bismarck Pack 04

Бренды по названию

Популярные бренды