4.
Select an option.
Note: The options that follow can show some differences in different controllers.
Option
Description
Edit name
Enters a description for the measurement site (default: serial number). Use the
description to identify the measurement locations (e.g., Aeration tank 1). The description
is saved with the measurement values in the controller data log.
Parameter
Selects the measured parameter:
• NT3200sc—NO
3
-N, NO
2
-N, NO
X
-N (default) or NO
3
, NO
2
, NO
X
• NT3100sc—NO
X
-N (default), NO
X
, NO
3
-N or NO
3
Unit
Sets the measurement units. Options: mg/L (default) or ppm
Measurement
interval
Sets the measurement interval. Options: 15, 30 seconds, 1, 5 (default), 10 or 30 minutes
Signal average
Sets the number of saved measurements the controller uses to calculate the average
measurement: 1 to 12 (default: 3). The signal average setting decreases the variability
of measurements. The controller shows and saves the average measurement to the
data log. In addition, the controller updates the relays and analog outputs to the average
measurement.
Cleaning interval
Sets the cleaning interval: 1 for each measurement (default), 1, 5, 10, 30 minutes, 1,
6 or 12 hours
Note: Changing the cleaning cycle can impact measurement results and the life time of
the wiper blades.
Wiper mode
Sets the wiper cleaning cycle:
•
Single
—The wiper makes one movement, from one side to another, with each
cleaning cycle.
•
Double A-B-A
—The wiper makes two movements with each cleaning cycle. Starts at
position A, moves to position B and then returns to position A. One cleaning cycle A-
B-A is counted as two movements.
•
Double B-A-B
(default)— The wiper makes two movements with each cleaning
cycle. Starts at position B, moves to position A and then returns to position B. One
cleaning cycle B-A-B is counted as two movements.
Note: A and B are the two final positions of the wiper movement. Select the correct
setting based on the probe installation. When the wiper stops, it must be in the top
position.
Figure 7 Wiper in position B
14
English
Содержание NT3100sc
