Hach H160 Скачать руководство пользователя

Страница: 7 / 52

Section 2

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or

consequential damages resulting from any defect or omission in this manual. The

manufacturer reserves the right to make changes in this manual and the products it

describes at any time, without notices or obligation. Revised editions are found on

the manufacturers website.

2.1 Safety information

Please read this entire manual before unpacking, setting up, or operating this

equipment. Pay attention to all danger and caution statements. Failure to do so

could result in serious injury to the operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired, do not

use or install this equipment in any manner other than that specified in this manual.

2.1.1 Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WA R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result

in death or serious injury.

C A U T I O N

Indicates a potentially hazardous situation which, if not avoided, could result in minor or

moderate injury.

N O T I C E

Indicates a situation that is not related to personal injury.

Содержание H160




















































Результаты поиска

Содержание H160

Отзывы:

Похожие инструкции для H160

Бренды по названию

Популярные бренды

Hach H160, Руководство пользователя

Результаты поиска

Содержание H160

Отзывы:

Похожие инструкции для H160

Бренды по названию

Популярные бренды