manualshive.com logo in svg

Hach H160, Руководство пользователя

Поделиться
Скачать
Hach H160 Скачать руководство пользователя страница 31

29

Section 6

Conductivity & TDS Operations

6.1 Set the Conductivity options

6.1.1 Set the conductivity calibration points

The meter stores up to five calibration points. Stored conductivity calibration points 

can be viewed, and are displayed in order of lowest to highest conductivity value.

1.

Push 

SETUP 

then push 

COND 

to put in the conductivity setup mode.

2.

Push the arrow keys until the conductivity calibration review screen is 

displayed.

Note: “- - - -” will be displayed if there are no stored conductivity calibration points.

3.

Push 

ENTER

. The first calibration point currently being used is shown. 

4.

Push the arrow keys to scroll to view other currently used calibration values.

6.1.2 Set the conductivity temperature

Conductivity varies greatly with temperature. The conductivity Automatic 
Temperature Compensation (ATC) adjusts conductivity measurements to factor out 
the conductivity changes in the reading caused by temperature. The readings are 
referenced to or “normalized” at a standard temperature. The options are 20 °C or 
25 °C. The ATC will give the equivalent conductivity or TDS of a solution normalized 
at 20 °C or 25 °C.

 

Default is 25 °C

1.

Push 

SETUP 

then push 

COND

.

Содержание H160





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды