manualshive.com logo in svg

H3C WA Series, Справочник команд второго уровня

Поделиться
Скачать
H3C WA Series Скачать руководство пользователя страница 77

 

69

 

stp priority 

Syntax 

stp 

[ 

instance

 

instance-id

 ] 

priority

 priority

 

undo stp

 [ 

instance

 

instance-id

 ] 

priority

 

View 

System view 

Default level 

2: System level 

Parameters 

instance

 

instance-id

: Sets the priority of the device in a MSTI. The 

instance-id

 argument ranges from 0 to 

15, where 0 represents the CIST. 

priority

: Specifies a device priority, ranging from 0 to 61440 in steps of 4096 (as in 0, 4096, 8192). You 

can set up to 16 priority values on the device. The smaller the value, the higher the device priority. 

Description 

Use 

stp priority 

to set the priority of the device.  

Use 

undo stp priority

 to restore the default priority.  

By default, the device priority is 32768. 
To set the priority of an MSTP device in a specific MSTI, use this command with the MSTI specified. To set 
the priority of an MSTP device in the CIST or an STP/RSTP device, use this command without specifying 

any MSTI. 

Examples 

# In MSTP mode, set the device priority to 4096 in MSTI 1.  

<Sysname> system-view 

[Sysname] stp instance 1 priority 4096 

stp region-configuration 

Syntax 

stp region-configuration 
undo stp region-configuration 

View 

System view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

stp region-configuration

 to enter MST region view.  

Содержание WA Series






































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды