manualshive.com logo in svg

H3C WA Series, Справочник команд второго уровня

Поделиться
Скачать
H3C WA Series Скачать руководство пользователя страница 125

 

117 

View 

VLAN interface view 

Default level 

2: System level 

Parameters 

dial-bundle-number

 

number

: Specifies the dialer bundle number corresponding to a PPPoE session, in 

the range of 1 to 255. A dialer bundle number uniquely identifies a PPPoE session, it can also be used 

as a PPPoE session ID. 

no-hostuniq

: Specifies the client not to carry the Host-Uniq field. By default, the Host-Uniq field

 

is carried. 

diagnose

: Specifies the working mode of the PPPoE session to diagnostic.  

interval 

seconds

: Specifies the interval (in seconds) between two diagnostic PPPoE sessions. The 

seconds

 

argument ranges from 5 to 65535. The default value is 120.  

idle-timeout

 

seconds

: Specifies the PPPoE session idle time. The 

seconds

 argument ranges from 1 to 

65535. If this option is specified, the PPPoE session works in packet-triggered mode; if this option and the 

diagnose

 keyword are not specified, the PPPoE session established works in permanent mode.  

queue-length

 

packets

: Specifies the number of the packets that can be cached before the PPPoE session 

is established. The 

packets

 argument ranges from 1 to 100 and defaults to 10. This option becomes valid 

only when the 

idle-timeout

 keyword is configured.  

Description 

Use 

pppoe-client

 to establish a PPPoE session and specify the dialer bundle corresponding to the session.  

Use 

undo pppoe-client

 to remove a PPPoE session. 

By default, no PPPoE session is established. 
You can establish multiple PPPoE sessions on a VLAN interface, or a VLAN interface can belong to 
multiple dialer bundles. However, a dialer bundle can correspond to only one VLAN interface. Each 

PPPoE session uniquely corresponds to a dialer bundle. If a VLAN interface in a dialer bundle of a dialer 

interface is used to establish a PPPoE session, you cannot add any interfaces to the dialer bundle.  
A PPPoE session works in one of these three modes: permanent, packet-triggered, and diagnostic.  

•

 

Permanent mode: If you execute the 

pppoe-client

 command without specifying the 

idle-timeout

 

seconds

 option or the 

diagnose

 keyword, the device initiates a PPPoE call to establish a PPPoE 

session immediately if the physical line is up. After the PPPoE session is established, it can only be 

terminated by the 

undo pppoe-client

 command. 

•

 

Packet-triggered mode: If you execute the 

pppoe-client

 command with the 

idle-timeout

 

seconds

 

option specified, the device tries to establish the PPPoE session only when it has data to transmit. For 

a PPPoE session working in this mode, if no data is transmitted across it within the period specified 
by the 

seconds

 argument, the PPPoE session will be terminated automatically. 

•

 

Diagnostic mode: If you execute the 

pppoe-client

 command with the 

diagnose

 keyword specified, 

the device initiates a PPPoE call to establish a PPPoE session immediately after this command is 

configured, and terminates the current PPPoE session and then establishes another PPPoE session 

each time the interval specified by 

interval 

seconds 

expires. By periodically establishing and 

terminating PPPoE sessions, this function can be used to detect whether the PPPoE link is normal. 

Only one diagnostic PPPoE session can be established on each device.  

Related commands: 

reset pppoe-client

. 

 

Содержание WA Series






































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды