H3C WA Series Скачать руководство пользователя страница 118

Страница: 118 / 133

110

Examples

# Set the username for CHAP authentication as

Root

on interface Dialer 1.

<Sysname> system-view

[Sysname] interface Dialer 1

[Sysname-Dialer1] ppp chap user Root

ppp ipcp remote-address forced

Syntax

ppp ipcp remote-address

forced

undo ppp ipcp remote-address

forced

View

Dialer interface view

Default level

2: System level

Parameters

None

Description

Use

ppp ipcp remote-address forced

to configure a device to assign an IP address to the peer by force.

This command also disables the peer from using a locally configured IP address.
Use

undo ppp ipcp remote-address

forced

to cancel the configuration.

By default, the peer is allowed to use its locally configured IP address. The local end assigns an IP

address to the peer only when being explicitly requested to do so. When the peer has already an IP

address, the local end will not assign one to the peer.
To disable the peer from using a locally configured IP address, perform the

ppp ipcp remote-address

forced

command.

Related commands:

remote address

Examples

# Configure an optional IP address 10.0.0.1 on interface Dialer 1 for the peer.

<Sysname> system-view

[Sysname] interface Dialer 1

[Sysname-Dialer1] remote address 10.0.0.1

# Configure IP address 10.0.0.1 on interface Dialer 1 for the peer and assign the IP address to the peer
by force.

<Sysname> system-view

[Sysname] interface Dialer 1

[Sysname-Dialer1] remote address 10.0.0.1

[Sysname-Dialer1] ppp ipcp remote-address forced

Содержание WA Series






































































































































Результаты поиска

Содержание WA Series

Отзывы:

Бренды по названию

Популярные бренды

H3C WA Series, Справочник команд второго уровня

Результаты поиска

Содержание WA Series

Отзывы:

Бренды по названию

Популярные бренды