manualshive.com logo in svg

H3C WA Series, Справочник команд второго уровня

Поделиться
Скачать
H3C WA Series Скачать руководство пользователя страница 24

16 

View 

Any view 

Default level 

1: Monitor level 

Parameters 

|

: Filters command output by specifying a regular expression. For more information about regular 

expressions, see 

Fundamentals Configuration Guide

. 

begin

: Displays the first line that matches the specified regular expression and all lines that follow. 

exclude

: Displays all lines that do not match the specified regular expression. 

include

: Displays all lines that match the specified regular expression. 

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. 

Description 

Use 

display loopback-detection 

to display the status of the loopback detection function. 

If loopback detection is enabled, this command also displays the detection interval and ports in a loop 
condition. 

Examples 

# Display information about loopback detection.

 

<Sysname> display loopback-detection 

 Loopback-detection is running. 

 Detection interval is 30 seconds. 

 No port is detected with loopback. 

Table 5

 

Command output 

Field Description 

Detection interval time is 30 seconds. 

Loopback detection interval is 30 seconds. 

No port is detected with loopback. 

No loops are detected on ports. 

 

flow-interval 

Syntax 

flow-interval 

interval 

undo flow-interval 

View 

System view 

Default level 

2: System level 

Parameters 

interval

: Sets the statistics polling interval, in seconds. It ranges from 5 to 300 and must be a multiple of 

5. 

Содержание WA Series






































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды