H3C WA Series Скачать руководство пользователя страница 106

Страница: 106 / 133

You can use a nonexistent VLAN as the PVID for a trunk port. If you remove the PVID of a trunk port with

the

undo vlan

command, it does not affect the setting of the PVID on the port.

You must use the

port trunk permit vlan

command to configure the trunk port to allow and forward

packets from the PVID.
Related commands:

port link-type

and

port trunk permit vlan

Examples

# Configure VLAN 100 as the PVID of the trunk port GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

[Sysname-GigabitEthernet1/0/1] port trunk pvid vlan 100

reset counters interface vlan-interface

Syntax

reset counters interface

vlan-interface

[

vlan-interface-id

]

View

User view

Default level

2: System level

Parameters

vlan-interface-id

: Specifies a VLAN interface number.

Description

Use

reset counters interface vlan-interface

to clear the statistics on a VLAN interface.

Before collecting the traffic statistics within a specific period of time on an interface, you must clear the

existing statistics first.
If the

vlan-interface-id

argument is not specified, this command clears the statistics of all VLAN interfaces.

If the

vlan-interface-id

argument is specified, this command clears the statistics of the specified VLAN

interface.
Related commands:

display interface vlan-interface

Examples

# Clear the statistics on VLAN-interface 2.

<Sysname> reset counters interface vlan-interface 2

shutdown

Syntax

shutdown
undo shutdown

Содержание WA Series






































































































































Результаты поиска

Содержание WA Series

Отзывы:

Бренды по названию

Популярные бренды

H3C WA Series, Справочник команд второго уровня

Результаты поиска

Содержание WA Series

Отзывы:

Бренды по названию

Популярные бренды