H3C S3610-28P Скачать руководство пользователя страница 964

Страница: 964 / 1547

Operation Manual – ARP
H3C S3610&S5510 Series Ethernet Switches

Chapter 1 ARP Configuration

1-2

The following explains the fields in

Figure 1-1

Hardware type: This field specifies the hardware address type. The value “1”

represents Ethernet.

Protocol type: This field specifies the type of the protocol address to be mapped.

The hexadecimal value “0x0800” represents IP.

Hardware address length and protocol address length: They respectively specify

the length of a hardware address and a protocol address, in bytes. For an Ethernet

address, the value of the hardware address length field is "6”. For an IP(v4)

address, the value of the protocol address length field is “4”.

OP: Operation code. This field specifies the type of ARP message. The value “1”

represents an ARP request and “2” represents an ARP reply.

Sender hardware address: This field specifies the hardware address of the device

sending the message.

Sender protocol address: This field specifies the protocol address of the device

sending the message.

Target hardware address: This field specifies the hardware address of the device

the message is being sent to.

Target protocol address: This field specifies the protocol address of the device the

message is being sent to.

1.1.3 ARP Address Resolution Process

Suppose that Host A and Host B are on the same subnet and that Host A sends a

message to Host B, as show in

Figure 1-2

. The resolution process is as follows:

1) Host A looks in its ARP mapping table to see whether there is an ARP entry for

Host B. If Host A finds it, Host A uses the MAC address in the entry to encapsulate

the IP packet into a data link layer frame and sends the frame to Host B.

2) If Host A finds no entry for Host B, Host A buffers the packet and broadcasts an

ARP request, in which the source IP address and source MAC address are

respectively the IP address and MAC address of Host A and the destination IP

address and MAC address are respectively the IP address of Host B and an

all-zero MAC address. Because the ARP request is sent in broadcast mode, all

hosts on this subnet can receive the request, but only the requested host (namely,

Host B) will process the request.

3) Host B compares its own IP address with the destination IP address in the ARP

request. If they are the same, Host B saves the source IP address and source

MAC address into its ARP mapping table, encapsulates its MAC address into an

ARP reply, and unicasts the reply to Host A.

After receiving the ARP reply, Host A adds the MAC address of Host B into its ARP

mapping table for subsequent packet forwarding. Meanwhile, Host A

encapsulates the IP packet and sends it out.

Содержание S3610-28P












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S3610-28P

Отзывы:

H3C S3610-28P, Руководство по эксплуатации, Страница: 964 / 1547

Результаты поиска

Содержание S3610-28P

Отзывы: