manualshive.com logo in svg

H3C S3610-28P, Руководство по эксплуатации, Страница: 832 / 1547

Поделиться
Скачать
H3C S3610-28P Скачать руководство пользователя страница 832

Operation Manual – Multicast Protocol 
H3C S3610&S5510 Series Ethernet Switches 

Chapter 7  MSDP Configuration

 

7-12 

7.4.3  Configuring an MSDP Mesh Group  

An AS may contain multiple MSDP peers. You can use the MSDP mesh group 

mechanism to avoid SA message flooding among these MSDP peers and optimize the 

multicast traffic.  

On one hand, an MSDP peer in an MSDP mesh group forwards SA messages from 

outside the mesh group that have passed the RPF check to the other members in the 

mesh group; on the other hand, a mesh group member accepts SA messages from 

inside the group without performing an RPF check, and does not forward the message 

within the mesh group either. This mechanism not only avoids SA flooding but also 

simplifies the RPF check mechanism, because BGP is not needed to run between 

these MSDP peers.  

By configuring the same mesh group name for multiple MSDP peers, you can create a 

mesh group with these MSDP peers.  

Follow these steps to create an MSDP mesh group:  

To do... 

Use the command... 

Remarks 

Enter system view 

system-view 

— 

Enter MSDP view 

msdp 

— 

Create an MSDP peer as 
a mesh group member  

peer peer-address 
mesh-group

 

name 

Required 

An MSDP peer does not 
belong to any mesh group 
by default 

 

 

 

  Note: 

z

 

Before grouping multiple routers into an MSDP mesh group, make sure that these 

routers are interconnected with one another.  

z

 

If you configure more than one mesh group name on an MSDP peer, only the last 

configuration is effective.  

 

7.4.4  Configuring MSDP Peer Connection Control  

MSDP peers are interconnected over TCP (port number 639). You can flexibly control 

sessions between MSDP peers by manually deactivating and reactivating the MSDP 

peering connections. When the connection between two MSDP peers is deactivated, 

SA messages will no longer be delivered between them, and the TCP connection is 

closed without any connection setup retry, but the configuration information will remain 

unchanged.  

Содержание S3610-28P












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов