manualshive.com logo in svg

H3C S3610-28P, Руководство по эксплуатации, Страница: 279 / 1547

Поделиться
Скачать
H3C S3610-28P Скачать руководство пользователя страница 279

Operation Manual – IPv6 
H3C S3610&S5510 Series Ethernet Switches 

Chapter 1  IPv6 Basics Configuration

 

1-11 

 

Figure 1-5 

Working procedure of the PMTU discovery 

The working procedure of the PMTU discovery is as follows: 

1)  The source host uses its MTU to fragment packets and then sends them to the 

destination host. 

2) 

If the MTU supported by the forwarding interface is less than the packet size, the 

forwarding device will discard the packet and return an ICMPv6 error packet 

containing the interface MTU to the source host. 

3) 

After receiving the ICMPv6 error packet, the source host uses the returned MTU to 

fragment the packet again and then sends it. 

4) 

Step 2 to step 3 are repeated until the destination host receives the packet. In this 

way, the minimum MTU of all links in the path from the source host to the 

destination host is determined. 

1.1.5  Introduction to IPv6 DNS 

In the IPv6 network, a Domain Name System (DNS) supporting IPv6 converts domain 

names into IPv6 addresses, instead of IPv4 addresses. 

However, just like an IPv4 DNS, an IPv6 DNS also covers static domain name 

resolution and dynamic domain name resolution. The function and implementation of 

these two types of domain name resolution are the same as those of an IPv4 DNS. For 

details, refer to 

DNS Configuration

. 

Usually, the DNS server connecting IPv4 and IPv6 networks not only contain A records 

(IPv4 addresses), but also AAAA records (IPv6 addresses). The DNS server can 

convert domain names into IPv4 addresses or IPv6 addresses. In this way, the DNS 

server implements the functions of both IPv6 DNS and IPv4 DNS. 

1.1.6  Protocols and Standards 

Protocols and standards related to IPv6 include: 

z

 

RFC 1881: IPv6 Address Allocation Management 

z

 

RFC 1887: An Architecture for IPv6 Unicast Address Allocation 

z

 

RFC 1981: Path MTU Discovery for IP version 6 

Содержание S3610-28P












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов