background image

10 

     

 

 

 

M i g h t y   M u l e   3 5 2

DRIVE

• Low friction screw drive (linear actuator) rated for -5 ºF to +160 ºF (-21 ºC to +71 ºC). 

• Powered by a 12 V motor with integral case hardened steel gear reducer.  Motor speed reduced to 260 rpm.  

Generates 520 inch lb. of torque at 12 V.

• Maximum opening arc of 110º.  Approximate  opening time (90º): 18 seconds, depending on weight of gate.

POWER

• The system is powered by a 12 Vdc automotive or marine battery. 

• Battery charge is maintained by a 120 Vac, 18 Vac output transformer [rectified to 14.5 Vdc (40 VA) through 

the GTO control board] or by

 

optional GTO Solar Panels [the panel should generate minimum of 10 W at

  600 mA].  A diode on the control board prevents battery discharge. 

 

 

IMPORTANT: 

Never use both transformer and solar panel - this will damage the battery and  control board.

• One (1) blade-style control board fuse is rated for 15 A.

   

NOTE: The transformer should not be directly connected to any battery.  Do not replace fuses with  

 

higher ampere rated fuses; doing so will void your warranty and may damage your control board.

CONTROL

  GTO

 microprocessor-based control board is set for dual leaf, pull-to-open gate installations.  DIP switches can 

be adjusted to accommodate an optional kit for push-to-open gates 

(see Accessory Catalog).

• Control board has temperature compensated circuits.

• A circuit on the control board regulates charging.  "Sleep draw" is 25 mA; "active draw" is 2 to 5 A.

• Auto-memorization of digital transmitter code.  

  

GTO remote-mounted RF receiver tuned to 318 MHz. 

• Opener length with push-pull tube fully retracted is 37

1

/

4

", mounting point to mounting point. Max stroke 19".

• Adjustable auto-close timer (OFF to 120 s), and obstruction sensitivity.

• Power terminal bock accommodates a transformer or solar panels.

• DIP switches simplify setup of gate opener.

• Accessory terminal block fully compatible with all Mighty Mule access controls.

• Control board allows connection of safety edge sensors and photoelectric sensors.

• Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing.

OPERATIONAL CAPACITY

• The Gate Capacity Chart shows approximate cycles, per day, you can expect from the Mighty Mule 352 Au

-

tomatic Gate Opener when powered with a transformer. Actual cycles may vary slightly depending upon the 

type and condition of gate and installation.

MIGHTY MULE® 352 E-Z GATE OPENER

Technical Specifications  

* These specifications are subject

   to change without notice.

Gate W

eight 

Gate Length 

Number of Cycles Per Day 

Mighty Mule 352 Gate Capacity /Cycle Chart 

Estimated number of daily cycles, based on use with a transformer and one(1) 12 Volt battery.

550 lbs. 
450 lbs. 
350 lbs. 
250 lbs. 
150 lbs. 
100 lbs. 

50 lbs. 

62
67
72
77
82
87
92

5’ - 6’

57
62
67
72
77
82
87

8’

57
62
67
72
77
82

10’

57
62
67
72
77

12’

57
62
67
72

14’

57
62
67

16’

NR 
NR 
NR 
NR 

NR 
NR 
NR 

NR 
NR 

NR 

 

NOTE: BALL BEARING HINGES SHOULD BE USED ON ALL GATES WEIGHING OVER 250 LB.

 

To determine the number of cycles the gate opener will perform using solar panels, please see the specifications 

listed on 

page 22

 or call

 (800) 543-1236 

or 

(850) 575-4144 

for more information.

 

 

* An operation cycle is one full opening and closing of the gate.

NOTE: "NR"

 

indicates 

this size and weight 
combination is not 
recommended for the 
Mighty Mule 352.

Содержание Mighty Mule 352

















































Отзывы: