GTO Mighty Mule 352 Скачать руководство пользователя страница 47

Страница: 47 / 48

M i g h t y M u l e 3 5 2

Accessories are Available From Your Retail Store

E-Z GATE OPENERS

ACCESSORIES

Solar Panel (FM123) 10 watt (FM121) 5 watt

- requires two - 5 watt panels

The

Solar Panel

is a 10 watt solar powered battery charger for use with the

FM350 & FM352

gate

operator systems. Particularly suited for remote installations, each

Solar Panel

comes with tubular

steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire

for additional wire). The

Mighty Mule® 352

control board has clearly labeled terminal connections

for easy installation of the

Solar Panel

. Installation in some regions of the world will require multiple

solar panels for adequate charging power. Dual gates require a minimum of 10 watts of solar

charging power. (5 watt panels require 2 panels)

Push Button Control (FM132)

Unlit doorbell button for remote entry or exit control. Wires directly to the control board and uses 16

gauge multi-stranded, dual conductor low voltage wire (sold separately).

Pin Lock (FM133)

The

Pin Lock

substitutes for the clevis pin at the front end of the Mighty Mule® 352 gate openers.

Helps prevent theft of the operator from the gate, while allowing quick release of the operator.

Key Chain Two Button Transmitter (FM134)

The Key Chain Transmitter is a dual button version of the

Mighty Mule®

single button entry

transmitter and has the same adjustable code settings. Used for 2 gates or 1 gate and garage door.

(battery is included)

Single Button Transmitter (FM135)

The

Mighty Mule®

entry transmitter, with adjustable code settings, is standard equipment with all

Mighty Mule® 352

systems. (battery is included)

Digital Keypad (FM137)

The specially designed digital keypad can be easily installed as a wireless or wired keypad. It can

be programmed to use up to 25 different personal identification number (PIN) codes. Each code is

face programmable with additional security features built in. Wired installations require 16 gauge,

low voltage, multi-stranded, dual conductor, direct burial wire (sold separately). Requires 3 AA

batteries (not included).

Mounting Post (FM100) - In Ground

This black powder coated pedestal is designed to provide convenient access to your keypad,

wireless intercom, or other access control device from your vehicle. With its break down design it

is easy to install and works well in most standard applications. Surface Mount Flanges (F102) and

Extensions (F103) for added height are available.

Mighty Mule® Vehicle Sensor (FM138)

The Gate Opening Sensor is designed for residential and agricultural applications and is compatible

with most Mighty Mule® automatic gate opener models (see Sensor Box for model compatibility).

The Sensor is an electromagnetic sensor, which offers 'hands free' operation of the Mighty Mule®

Gate Operator with a 12 ft. radius of detection of vehicles in motion.

A wireless version of the Gate Opening Sensor is available. (FM130)

Содержание Mighty Mule 352

















































Результаты поиска

Содержание Mighty Mule 352

Отзывы:

Бренды по названию

Популярные бренды

GTO Mighty Mule 352, Руководство по установке

Результаты поиска

Содержание Mighty Mule 352

Отзывы:

Бренды по названию

Популярные бренды