GT Grade Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 220

background image

79

PART 2

Operating and E-Bike (4 of 4)

Section A. Important Safety Information

GT Bicycle Owner’s Manual

Operating and E-Bike (4 of 4)

WARNINGS

Wired system control: If the drive system control device is detached from the mount or if the cables
are disconnected or damaged, the drive system will automatically shut off. If this happens, you will
have to stop the bike, turn the system off , re-attach the computer to the base, and then turn the
system back on to resume operation.

Wireless system control: In wireless control systems, the operation of the drive system is controlled
using radio frequencies without physical attachment. Therefore, ON/OFF activation is determined by
software programming. Please consult the manufacturer’s instructions for information on preventing
accidental activation or on restarting the drive system in the event of a recovery from a drive system
fault.

Your insurance policies - Your insurance policies (e.g., liability, property, and injury) may not provide
coverage for accidents involving the use of this bicycle. To determine if coverage is provided, you
should contact your insurance company or agent. Also, make sure your speed e-bike is insured and
registered according to the local laws.

Ride sensibly and safely around others - the application of power by means of the electric motor
assist means that riders can reach high speed. Riding faster increases the risks of serious accidents.

Watch out for other vehicles, cyclists, pedestrians, and animals where you ride. Always operate
under control and at a safe speed. Others may not be aware of you. It is your responsibility to
anticipate and to react to avoid accidents.

E-bikes are heavier than ordinary bikes - always park the bike in a suitable safe area away from
children, cars or animals that may come into contact with it. Park the bike so that it cannot fall over
and possibly result in injuries.

Do not ride into or attempt to ride through water or to submerge any part of the bike. If you ride
through water you can lose control of the bike or the drive-assist system can become disabled or
damage.

Y

ou can be severely injured, paralyzed, or killed in an accident if you ignore these warnings.

«
...
77
78
79
80
81
...
»

Содержание Grade





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grade

Бренд: Makita Страницы: 16

Бренд: BAFANG Страницы: 6

Бренд: SWAGTRON Страницы: 22

Бренд: Bontrager Страницы: 20

Vuka Alumina Clip

Бренд: Zipp Страницы: 2

Pedelec Groove*

Бренд: Raleigh Страницы: 397

Бренд: Cake Страницы: 36

Бренд: Worksman Страницы: 4

Orange Pure Innergy

Бренд: Gazelle Страницы: 92

Бренд: LYNE Страницы: 2

Бренд: Shulz Страницы: 24

BT C01.340.UART

Бренд: BAFANG Страницы: 34

Бренд: Cycle2Charge Страницы: 28

Бренд: Kalkhoff Страницы: 482

Бренд: b'Twin Страницы: 33

Бренд: Yakima Страницы: 30

Kompact Sports Trike

Бренд: KMX Karts Страницы: 14

Wireless Tech All-in -One Design

Бренд: dbRevO Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды