GT Grade Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 220

background image

201

PART 3

For all disc brakes:

STEP 9. Front Brake

GT Bicycle Owner’s Manual

Lift the front of the bike and spin the front wheel and apply the front brake very firmly. Hold the front
brake lever on very firmly with one hand, do not let go. With your other hand use a 5mm allen wrench to
tighten the two caliper mounting bolts. No final torque at this point, just tight.

Again, pick up the front of the bike and spin the front wheel. Do you see or hear dragging from the front
brake? Likely much less or no dragging.

If no drag, no noise, torque the two 5mm caliper mounting bolts to 7 Nm.

If there is some drag, some noise, again loosen the two caliper mounting bolts with the 5mm allen
wrench. Loosen just enough to be able to move the caliper with your hand. Pick up the front of the bike
and spin the front wheel. Apply the front brake very firmly. Hold the front brake lever on very firmly with
one hand, do not let go. With your other hand use the 5mm allen wrench to tighten the two caliper
mounting bolts. No final torque at this point, just tight. It is common for this process to take two or more
operations to properly adjust the brake.

See video instruction at:

https://support.gtbicycles.com/hc/en-us/articles/1500008322681-Dick-s-

Sporting-Goods-Avalanche-Assembly

For all disc brakes:

Note that it may take anywhere from 20 to 40 complete stops to “break-in” your disk brakes. You may
notice an increase in braking power after the first ride. Do not touch the disc brake rotors with your
fingers or expose them to oils and lubricants. These contaminants will significantly degrade braking
performance. Best practice is to clean the surfaces of the disc brake rotor with isopropyl alcohol.

WARNING

Do not touch or clean the rotor immediately after use, as the rotor may be very hot and could burn
you.

«
...
199
200
201
202
203
...
»

Содержание Grade





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grade

Бренд: Jetson Страницы: 24

Бренд: Quantum Страницы: 25

Бренд: Navibe Страницы: 8

Бренд: Puky Страницы: 48

Adventure SCREAM BPM170L

Бренд: Mactronic Страницы: 2

CHINOOK RAIN COVER

Бренд: Chariot Страницы: 4

e:i Shock Auto 2017

Бренд: Lapierre Страницы: 31

Urban iki Ta-ke

Бренд: OGK Страницы: 60

Бренд: Tower Hobbies Страницы: 11

Бренд: APLIC Страницы: 28

Бренд: Bontrager Страницы: 12

Бренд: Marzocchi Страницы: 79

Бренд: Cycle2Charge Страницы: 28

Бренд: Tern Страницы: 124

Бренд: Mavic Страницы: 2

Бренд: Marzocchi Страницы: 32

Бренд: hepco & becker Страницы: 4

Бренд: Let's Go Aero Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды