GT Grade Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 220

background image

91

PART 2

Rear Tire Clearance : Full Suspension

Section A. Important Safety Information

GT Bicycle Owner’s Manual

Rear Tire Clearance : Full Suspension

To check clearance:

1. Release all the air from the rear shock.

Remove the coil spring from coil shocks.
spring coil (removal should only be done
by a professional bike mechanic). Do not
disconnect or remove the shock.

2. Compress the suspension fully with the tire

inflated to its maximum inflation pressure.

3. At various points across the tire, measure

the distance between the tire and the
component or accessory.

4. If there is less than 10 mm of clearance

available, the component or accessory must
be adjusted or changed until l there is at
least 10 mm of clearance.

WARNINGS

Maintain 10 mm of clearance between rear
tire, any rear rack, saddle, seat post, frame
seat tube, or any mounted accessory.

Check following saddle or seat post
adjustments.

If you have questions maintaining tire
clearances for parts of your bike consult with
an Authorized Dealer or a professional
cycling mechanic.

You can be severely injured, paralyzed
or killed in an accident if you ignore this
warning.

10 mm

Applies to:

•

saddles

•

seat posts

•

rear racks

•

Dropper posts

•

any accessory with
possible collision with the
moving tire.

«
...
89
90
91
92
93
...
»

Содержание Grade





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grade

Бренд: BAFANG Страницы: 4

Бренд: Magura Страницы: 2

Бренд: NAKTO Страницы: 24

Бренд: R&G Страницы: 19

Sorbus City SUV

Бренд: WALDBIKE Страницы: 32

Бренд: QPlay Страницы: 6

Бренд: CORTINA Страницы: 36

Бренд: Krabat Страницы: 22

Бренд: Ridea Страницы: 2

Бренд: Ride1up Страницы: 23

Бренд: Richelieu Страницы: 2

Бренд: eelo Страницы: 12

Scamper S200 XL

Бренд: Lacros Страницы: 16

FB-NOVABIKE FBNB2201

Бренд: e-nova Страницы: 11

ULTEGRA RD-6500 - TECHNICAL

Бренд: DAHON Страницы: 1

Бренд: Five Страницы: 4

Бренд: Xiaomi Страницы: 9

Бренд: ibis Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды