GT Grade Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 220

background image

172

PART 3

STEP 6. Installing the Handlebar And Stem

138692 Rev 0 (04/22)

Assembling Your Bike

GT Bicycle Owner’s Manual

Stem to fork steering tube set up:

Be sure that any fork protection spacer has been removed from the dropouts, the bottom parts of the
fork.

Take the bike out of the carton and place the fork dropouts on the floor. Keep the fork aiming forward.
Pivot the stem so that it faces directly forward.

Find the stem clamping bolts on the back of the stem. These are the bolts that hold the stem/handlebar
assembly in place on the steering tube of the fork. Tighten these bolts using a torque wrench to the
torque value marked on the stem. If no torque marking is present, tighten to 7Nm.

Method B, Stem is attached to the handlebars:

Remove the plastic fork protector from the bottom of the fork.

Set the bike on the floor. The rear wheel is already installed. As you set the fork on the floor be sure that
the fork is aimed forward. This will make it possible for the bike to balance on the floor. Confirm that the
fork is oriented forward. One way to check this is that the brake caliper will be on the left side of the bike.

Now that the weight of the bike is pushing down on the fork remove the top cap. This is done by
un-threading the top cap bolt with a 5 mm allen wrench. Once loose, remove the top cap and bolt as an
assembly and set it nearby.

«
...
170
171
172
173
174
...
»

Содержание Grade





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grade

Бренд: Quantum Страницы: 32

Бренд: moon Страницы: 4

Ekar 13S Crankset

Бренд: CAMPAGNOLO Страницы: 112

Bikes with Threaded Headsets

Бренд: L.L.Bean Страницы: 7

Бренд: Cyrusher Страницы: 26

Бренд: Diamondback Страницы: 38

Бренд: Betzold Страницы: 4

Бренд: Union Страницы: 16

Бренд: Suzhou Kunteng Electronics Страницы: 2

MACRO high free

Бренд: O-Synce Страницы: 2

Бренд: Gazelle Страницы: 20

Бренд: Porsche Страницы: 46

Бренд: OKBABY Страницы: 61

Adventure CCAT2W-110930

Бренд: Cateye Страницы: 3

Бренд: BH Emotion Страницы: 122

Бренд: DAHON Страницы: 22

Бренд: SUPERNOVA Страницы: 9

M99 Tail Light 25

Бренд: SUPERNOVA Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды