Grundfos TPE 2 Series Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 70

background image

English (GB)

3

1. Symbols used in this document

2. Abbreviations and definitions

Warning
Prior to installation, read these installation and
operating instructions. Installation and operation
must comply with local regulations and accepted
codes of good practice.

Warning
If these safety instructions are not observed, it may
result in personal injury.

Warning
If these instructions are not observed, it may lead to
electric shock with consequent risk of serious
personal injury or death.

Warning
The surface of the product may be so hot that it may
cause burns or personal injury.

Warning
Risk of dropping objects which may cause personal
injury.

Warning
Escaping vapour involves the risk of personal injury.

Caution

If these safety instructions are not observed, it may
result in malfunction or damage to the equipment.

Note

Notes or instructions that make the job easier and
ensure safe operation.

AI

Analog input

AL

Alarm, out of range at lower limit

AO

Analog output

AU

Alarm, out of range at upper limit

Current sinking

The ability to draw current into the terminal and
guide it towards earth in the internal circuitry.

Current
sourcing

The ability to push current out of the terminal
and into an external load which must return it
to earth.

DI

Digital input

DO

Digital output

ELCB

Earth-leakage circuit breaker

FM

Functional module

GDS

Grundfos Digital Sensor.
Factory-fitted sensor in some Grundfos pumps.

GENIbus

Proprietary Grundfos fieldbus standard.

GFCI

Ground fault circuit interrupter.
(USA and Canada).

GND

Earth

Grundfos Eye

Status indicator light

LIVE

Low voltage with the risk of electric shock if the
terminals are touched.

OC

Open collector:
Configurable open-collector output.

PE

Protective earth

PELV

Protective extra-low voltage.
A voltage that cannot exceed ELV under
normal conditions and under single-fault
conditions, except earth faults in other circuits.

SELV

Safety extra-low voltage.
A voltage that cannot exceed ELV under
normal conditions and under single-fault
conditions, including earth faults in other
circuits.

TPE2

Single-head pump without factory-fitted
differential-pressure and temperature sensor.

TPE2 D

Twin-head pump without factory-fitted
differential-pressure and temperature sensor.

TPE3

Single-head pump with factory-fitted
differential-pressure and temperature sensor.

TPE3 D

Twin-head pump with factory-fitted
differential-pressure and temperature sensor.

«
1
2
3
4
5
...
»

Содержание TPE 2 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для TPE 2 Series

Бренд: Dairyland Страницы: 5

Бренд: Nitecore Страницы: 4

Бренд: Quivogne Страницы: 13

Бренд: Jet Страницы: 12

Бренд: Labnet Страницы: 12

Accublock D1301

Бренд: Labnet Страницы: 13

Бренд: Madsen Страницы: 206

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Nektar Страницы: 12

Бренд: Pari Страницы: 282

Бренд: quadient Страницы: 14

Бренд: Qu-Bit Electronix Страницы: 31

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: Yamaha Страницы: 48

Бренд: Igema Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды