Grundfos TPE 2 Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 70

background image

English (GB)

12

7.4.2 Connection terminals, standard functional module (FM

200)

The standard module has these connections:
• two analog inputs
• two digital inputs or one digital input and one open-collector

output

• Grundfos Digital Sensor input and output
• two signal relay outputs
• GENIbus connection.
See fig.

• Inputs and outputs

All inputs and outputs are internally separated from the
mains-conducting parts by reinforced insulation and
galvanically separated from other circuits.
All control terminals are supplied by safety extra-low voltage
(SELV), thus ensuring protection against electric shock.

• Signal relay outputs

– Signal relay 1:

LIVE:
Mains supply voltages up to 250 VAC can be connected to
this output.
SELV:
The output is galvanically separated from other circuits.
Therefore, the supply voltage or safety extra-low voltage
can be connected to the output as desired.

– Signal relay 2:

SELV:
The output is galvanically separated from other circuits.
Therefore, the supply voltage or safety extra-low voltage
can be connected to the output as desired.

• Mains supply, terminals N, PE, L or L1, L2, L3, PE
A galvanically safe separation must fulfil the requirements for
reinforced insulation including creepage distances and
clearances specified in EN 61800-5-1.

Note

Digital input 1 is factory-set to start/stop input where
an open circuit will result in stop.
A jumper has been factory-fitted between terminals 2
and 6. Remove the jumper if digital input 1 is to be
used as external start/stop or any other external
function.

Note

As a precaution, the wires to be connected to the
connection groups below must be separated from
each other by reinforced insulation in their entire
lengths.

«
...
10
11
12
13
14
...
»

Содержание TPE 2 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для TPE 2 Series

Бренд: B&K Страницы: 12

Бренд: Dairyland Страницы: 21

Бренд: Cadex Страницы: 300

Бренд: HABYS Страницы: 16

Бренд: Jacto Страницы: 12

Бренд: Oakworks Medical Страницы: 28

Бренд: ebm-papst Страницы: 10

CEAG Exit Cube 33822 LED CGLine+

Бренд: Eaton Страницы: 20

Бренд: swamp Страницы: 5

Бренд: Vision & Control Страницы: 32

Бренд: Grundfos Страницы: 43

Бренд: endolite Страницы: 158

Бренд: Lupine Страницы: 7

SystemRoMedic RiseAtlas450

Бренд: Handicare Страницы: 48

Allen-Bradley PowerFlex 755T Flux Vector Tuning

Бренд: Rockwell Automation Страницы: 116

Бренд: OmniCure Страницы: 2

GSE electronic ballast

Бренд: G-Systems Страницы: 38

Бренд: Qdot Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды