Grizzly T27710 Скачать руководство пользователя страница 110

Страница: 110 / 118

Reassembly

KohlerEngines.com

18 690 01 Rev. C

Install Throttle Plate

Install throttle plate with screws.

Install Engine Air Shroud

Install cylinder shroud. Torque screws to 8 N·m

(70.8 in. lb.).

Install Carburetor

1. Install a new insulator to cylinder head gasket onto

carburetor studs, followed by insulator, carburetor to

insulator gasket, carburetor, and air cleaner gasket.

2. Connect throttle link and dampening spring into their

respective holes on throttle lever.

Blower Housing/Control Panel Components

Governor Lever

Nut

Governor Spring

Throttle Link

Dampening Spring

Control Assembly

Carburetor

Retractable Starter

On/Off Wiring

Harness Bullet

Connector

Blower Housing

Oil Sentry

™

Wiring

Harness Bullet

Connector

Oil Sentry

™

Module

Oil Sentry

™

Bracket

Install Blower Housing

1. Position spark plug lead in molded clip in carburetor

insulator.

2. Install blower housing on crankcase with screws.

Torque screws to 10 N·m (88.5 in. lb.).

Install Electric Starter and Control Panel (if

equipped)

1. Align and mount electric starter onto crankcase.

Install and torque screws to 24 N·m (212 in. lb.).

2. Connect electrical leads for Oil Sentry

™

, ignition

module, key switch, relay, and starter.

3. Mount control panel to crankcase and secure with

screws. Ensure ground wires are placed between

screw and bracket. Torque screws to 24 N·m

(212 in. lb.).

Содержание T27710






















































































































Результаты поиска

Содержание T27710

Отзывы:

Похожие инструкции для T27710

Бренды по названию

Популярные бренды

Grizzly T27710, Руководство пользователя

Результаты поиска

Содержание T27710

Отзывы:

Похожие инструкции для T27710

Бренды по названию

Популярные бренды