Grizzly G1023S Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

Grizzly G1023S Скачать руководство пользователя страница 30

-28-

G1023S/G1023S110 Heavy-Duty 10'' Table Saw

Blade Selection

Choosing the correct blade for the job is essential
for the safe and efficient use of your table saw.
Ignoring this important step could result in dam-
age to the saw and serious injury to the operator.
Below are the most common saw blades and
their uses.

1. Rip Blade (shown in Figure 30): Used

for cutting with the grain. Typically, 10" rip
blades have between 20-40 teeth, a flat-top
ground profile (see

Figure 31 for saw tooth

profiles) and large gullets to allow for large
chip removal.

Figure 30. Ripping blade.

Test Run

1. Face the table saw and stand to the left of

the blade path.

2. With one finger on the START button and

one finger on the STOP button, turn the saw
on. Be ready to turn the saw off in case of
mishap.

3. Watch and listen to the saw. Note whether

there are any unusual sounds or excessive
vibrations.

4. If anything appears abnormal, immediately

turn off the saw, unplug it, and fix the prob-
lem. If a problem exists that is beyond the
scope of this manual, call our service depart-
ment.

5. If the saw is operating correctly, turn it off

and prepare to make a cut according to the
instructions outlined in this section.

Figure 31. Various saw tooth cutting profiles.

Flat

Top

Blade

Alternate

Top

Bevel

Alternate

Top Bevel

And

Raker

Triple

Chip

Blade

«
...
28
29
30
31
32
...
»

Содержание G1023S





















































Отзывы:

Нет отзывов