Grizzly G1023S Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 52

Grizzly G1023S Скачать руководство пользователя страница 29

G1023S/G1023S110 Heavy-Duty 10'' Table Saw

-27-

Pre-Run Check

SECTION 6: OPERATIONS

Before you begin to use your Model G1023
Series, you should give it a thorough inspection.
While making your inspection, ask yourself the
following questions:

1. Are all the fasteners tight?

2. Is the blade mounted correctly?

3. Is the saw stable?

4. Is it wired properly?

5. Is your electrical system properly config-

ured?

6. Have you checked your workpiece for obvi-

ous defects?

7. Are the V-belts properly tensioned and the

pulleys properly aligned?

8. Is the guard assembly installed and func-

tional?

9. Have you checked the saw blade clearance

when it is adjusted to varying angles and
depths?

10. Have you read all the warnings and directions

regarding the operation of this machine?

Keep loose clothing out

of the way of machin-

ery and keep hair pulled

back.

Wear safety glasses dur-

ing all operations on the

shaper. Failure to com-

ply may result in serious

personal injury.

Disconnect power to the

machine when perform-

ing any adjustments or

maintenance. Failure to

do this may result in seri-

ous personal injury.

Always wear a dust mask
when operating the table
saw. Using this machine
produces sawdust which
may cause allergic reac-
tions or respiratory prob-
lems.

NOTICE

The following section was designed to give

instructions on the basic operations of this

table saw. However, it is in no way com-

prehensive of every table saw application.

There are many different jigs that can be

built to increase safety, accuracy, and types

of cuts. WE STRONGLY RECOMMEND that

you read books, trade magazines, or get

formal training to maximize the potential of

your table saw.

«
...
27
28
29
30
31
...
»

Содержание G1023S





















































Отзывы:

Нет отзывов