Grizzly Pro Video r-THREE Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

background image

r3a-x2.0

23

want to make a note to yourself regarding the
behavior of this camera.

The zoom joystick is configurable – see the Advanced
Operations (

Zoom Speed

and

Configure Zoom

in

Table 1).

Preview (used for

r-ONE

only)

The composite video signal from the one remote
camera. Generally you will want to connect a
monitor to this feed to allow for remote viewing of
your camera. A monitor cable with a BNC connector
will be needed.

Interface
For the

r-ONE:

A powered interface which connects to the

r-THREE

Pan/Tilt Head with the r3a-ptzcable.

For the

r-THREE

and

r-THREE-LS

:

A powered interface which connects to the

r-THREE

Interface Box with the r3a-intcable.

Picture 1d –

r-THREE

Control Head

Side View

«
...
22
23
24
25
26
...
»

Содержание r-THREE

































































Отзывы:

Нет отзывов

Похожие инструкции для r-THREE

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Accel Страницы: 8

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Fingertips Lab Страницы: 15

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренд: Swagelok Страницы: 16

Бренд: Phoenix Contact Страницы: 56

Бренд: Mitsubishi Страницы: 16

Бренд: HTW Страницы: 88

Бренд: Powtran Страницы: 40

Series RHCN-7000

Бренд: Omega Engineering Страницы: 2

xComfort CHSZ-12/03

Бренд: Eaton Страницы: 4

Бренд: WAM Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Absima Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды