Grizzly Pro Video r-THREE Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 64

background image

r3a-x2.0

46

CAM MODE

Press the MODE Button until the CAM light is on. This puts
the system in CAM MODE. The Display will initially look
like:

Using the Menu Knob when in CAM MODE:

1.

Use the Menu Knob to find the Camera Command
that you wish to remotely control on the current
Preview camera. See Table 4 - LANC Camera
Commands. (e.g.

Camera Commands Display

)

2.

Select the command by pressing the Menu Knob.

3.

If the

Camera Command Display

is on you will likely

see some indication that the mode is on or off. See
your camera manual for details.

You can exit from CAM MODE at any time by pressing the
MODE button.

Table 4 -
LANC Camera
Commands

With

Camera Commands Menu

selected, you will enable the camera
menu on your physical camera. See
the CAM MODE Example on page 39
for additional details and usage.

You must also have

Camera

Commands Display

selected to see

the camera menu on the Preview
Monitor.

«
...
45
46
47
48
49
...
»

Содержание r-THREE

































































Отзывы:

Нет отзывов

Похожие инструкции для r-THREE

Бренд: Lawler Страницы: 5

Бренд: GE Страницы: 8

Бренд: Sole Diesel Страницы: 8

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: jcm-tech Страницы: 8

Бренд: Ultra Start Страницы: 8

Бренд: Watts Страницы: 24

Бренд: Xilinx Страницы: 2

Бренд: Koer Страницы: 6

Бренд: Universal Remote Страницы: 20

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: M-system Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды