Greenlee Ultra Tugger UT10-22 Скачать руководство пользователя страница 19

Страница: 19 / 116

Ultra Tugger

10 Cable Puller and Pulling Packages

Greenlee Tools, Inc.

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Cable Pulling Principles

(cont’d)

Tailing the Rope

The rope must be pulled off of the capstan as the pull

progresses. The rope that has left the capstan is the

“tail.” The process of pulling the rope off of the capstan

is called

tailing the rope

The resistance of the cable varies throughout the dura-

tion of the cable pull. Changes in resistance are

due to characteristics of the rope, changes in conduit

direction, and changes in the amount of friction. The

“feel” of the rope provides this information about the

pull. This is called

tactile feedback

. Adjust the tailing

force as necessary to compensate for these changes.

Control of the Pull

Decreasing the tailing force will decrease the pulling

force, until the rope slips on the capstan and the pull

stops. This provides a high level of control over the

progress of the cable pull.
Do not allow the rope to slip on the capstan for more

than a few moments. If it becomes necessary to com-

pletely stop a pull, shut off the puller and maintain

enough tailing force to hold cable in place. Tie the rope

off to hold it in place.

Amount of Tailing Force

While the rope and cable are under tension, it is impor-

tant to maintain the proper amount of tailing force.

Too little

tailing force will allow the rope to slip on the

capstan. This will build up excessive heat and acceler-

ate rope wear, increasing the possibility of breaking the

rope.
The proper amount of tailing force will stop the rope

from slipping on the capstan and produce a sufficient

amount of pulling force to pull in the rope and cable.

Too much

tailing force is any amount more than is nec-

essary to stop the rope from slipping on the capstan.

Excessive tailing force will not increase the pulling force

or pulling speed.

Number of Wraps of Rope Around the Capstan

An experienced operator should choose the number

times the rope is wrapped around the capstan.
The proper number of wraps allows the operator to

control the progress of the pull with a comfortable

amount of effort.
Using

too few

wraps requires a large tailing force to

accomplish the pull. Using too few wraps also makes

the rope more likely to slip on the capstan. This builds

up heat and accelerates rope wear.
Using

too many

wraps causes the rope to grab the

capstan tighter. This accelerates rope wear, wastes

power, and increases the possibility of a rope overlap.

Using too many wraps also reduces tactile feedback,

so you receive less information about the pull. You

cannot quickly relax the tailing force when there are too

many wraps.
If the rope becomes difficult to tail, add another wrap

of rope. Turn off the puller and release all of the tension

in the rope. Add a wrap and resume pulling. Be aware,

however, that some pulls will require tension to hold

the cables in place. In these cases, do not attempt to

release all of the tension and add a wrap of rope. You

will need to anticipate the number of wraps before start-

ing the pull.

Preventing Rope Overlap

Do not allow the rope to become overlapped on the

capstan during a pull.
A rope overlap will make it impossible to continue

or back out of the pull.
If the rope becomes overlapped, you will lose control

of the pull —the rope will advance with no tailing force

and will not feed off of the capstan. The capstan will not

allow you to reverse the direction of the rope, so you

cannot back out of an overlap.
Set up the puller properly. The rope ramp and tapered

capstan are intended to prevent rope overlap. Refer

to the instructions in the “Operation” section of this

manual.
Every wrap of the rope must remain in direct contact

with the capstan. During the pull, take great care to

prevent the incoming rope from riding up and overlap-

ping the next wrap. If an overlap begins to develop,

immediately relax the tailing force on the rope so that

the rope can feed back toward the conduit or tray.

When the rope resumes its normal path, apply tailing

force and continue the pull.
There is no suggested remedy for a rope overlap.

Do not allow the rope to overlap!

Содержание Ultra Tugger UT10-22





















































































































Результаты поиска

Содержание Ultra Tugger UT10-22

Отзывы:

Похожие инструкции для Ultra Tugger UT10-22

Бренды по названию

Популярные бренды

Greenlee Ultra Tugger UT10-22, Инструкция по эксплуатации

Результаты поиска

Содержание Ultra Tugger UT10-22

Отзывы:

Похожие инструкции для Ultra Tugger UT10-22

Бренды по названию

Популярные бренды