3
Kitchen Fan Control Center
®
Installation
Control Box Mounting
Locate an area with enough space to mount the control
box and fasten to the wall . Use appropriate type
fasteners depending on the mounting location . Avoid
installing the control box in environments with high
magnetic and/or radio frequency interference .
NOTE
Control box may be factory mounted . If so, continue
to the next section .
Switch Mounting
Locate an area with enough space to mount the
switches junction box and fasten to the wall .
NOTE
If the switches were NOT shipped loose, provided in a
separate junction box, continue to the next section .
Temperature Sensor(s) - Hood Mounting
NOTE
Temperature sensor(s) will be provided only if the
digital temperature interlock option was configured/
ordered with the unit . If it wasn’t, continue to the next
section .
Temperature sensor(s) may be factory installed . If so,
continue to the next section .
2 . Find a spot for the sensor in the flat space that will
not interfere with the fire suppression nozzles and
that is not within 12 inches (304 .8 mm) of any light
fixtures . Cut a 3/4 to 7/8-inch (19 .0 to 22 .2 mm)
diameter hole in the flat spot of the capture tank .
1 . Locate flat area(s) at the top interior of the hood in
front of the filters, towards the front of the hood .
CAD Drawing from Tyler Schilling
Emailed to Barb on March 22, 2011
Updated the PN of the Resistive Temperature Detector to 384925 as provided in edits from Aaron Van Krey - October 18, 2012
Updated the for the Digital Temperature Interlock IOM - edits provided by Aaron Van Krey - November 20, 2016
Octagon Extension
PN 830125
Lock Washer
Nut
Compression Seal
PN 463570
Gasket
J-Box Plate
PN 732396
Temperature Sensor
PN 384925
Octagon Cover
PN 380926
2 inch typical
(50.8 mm)
19.525 inches
(495.9 mm)
3 inch air space
(76.2 mm)
Additional Octagon Extension
(Optional)
PN 830125
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
Hood Surface
1
2
3
1.
PLACE THE J-BOX PLATE INSIDE OF THE OCTAGON EXTENSION
RING, AND PLACE OVER HOLE.
2.
DISASSEMBLE THE COMPRESSION SEAL AND PLACE THROUGH
THROUGH HOLE AND J-BOX PLATE AS SHOWN. TIGHTEN THE NUT
INSIDE THE OCTAGON EXTENSION RING.
1.
PLACE THE THERMOSTAT THROUGH THE COMPRESSION
COMPRESSION SEAL AND TIGHTEN THE COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
CUT A 0.75" - 0.875" HOLE IN THE FLAT SPOT OF THE
CAPTURE TANK OF THE HOOD. KEEP 12" AWAY FROM
ANY LIGHT FIXTURE.
Sensor Install
(cutout area)
Exhaust Area
Supply Area
(optional)
HOOD PLAN VIEW
P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-0410
TITLE
DRAWN BY
ECO
B
ENG. REF.
DATE
SUPERSEDES
SCALE
CAD DRAWING NO.
MROCZENSKI_L
12/02/2009
1/4
IAN29890
INSTR, ADJ. TEMP
INTERLOCK IN FLAT
SPOT
Top View of Exhaust Hood
CAD Drawing from Tyler Schilling
Emailed to Barb on March 22, 2011
Updated the PN of the Resistive Temperature Detector to 384925 as provided in edits from Aaron Van Krey - October 18, 2012
Updated the for the Digital Temperature Interlock IOM - edits provided by Aaron Van Krey - November 20, 2016
Octagon Extension
PN 830125
Lock Washer
Nut
Compression Seal
PN 463570
Gasket
J-Box Plate
PN 732396
Temperature Sensor
PN 384925
Octagon Cover
PN 380926
2 inch typical
(50.8 mm)
19.525 inches
(495.9 mm)
3 inch air space
(76.2 mm)
Additional Octagon Extension
(Optional)
PN 830125
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
Hood Surface
1
2
3
1.
PLACE THE J-BOX PLATE INSIDE OF THE OCTAGON EXTENSION
RING, AND PLACE OVER HOLE.
2.
DISASSEMBLE THE COMPRESSION SEAL AND PLACE THROUGH
THROUGH HOLE AND J-BOX PLATE AS SHOWN. TIGHTEN THE NUT
INSIDE THE OCTAGON EXTENSION RING.
1.
PLACE THE THERMOSTAT THROUGH THE COMPRESSION
COMPRESSION SEAL AND TIGHTEN THE COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
CUT A 0.75" - 0.875" HOLE IN THE FLAT SPOT OF THE
CAPTURE TANK OF THE HOOD. KEEP 12" AWAY FROM
ANY LIGHT FIXTURE.
Sensor Install
(cutout area)
Exhaust Area
Supply Area
(optional)
HOOD PLAN VIEW
P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-0410
TITLE
DRAWN BY
ECO
B
ENG. REF.
DATE
SUPERSEDES
SCALE
CAD DRAWING NO.
MROCZENSKI_L
12/02/2009
1/4
IAN29890
INSTR, ADJ. TEMP
INTERLOCK IN FLAT
SPOT
