Greenheck KFCC, Инструкция по установке, эксплуатации и обслуживанию

Страница: 14 / 24

14
Kitchen Fan Control Center
®
Factory Parameters
To access/adjust all factory parameters, follow these
instructions:
1 . Press and hold
OUT1 OUT2
°C
°F
Set Set
A
U
X
button for 30 seconds or until ‘0’
appears .
NOTE
The controller is pre-programmed at the factory to
operate based on how many sensors were selected .
Adjustments (outside of the set point temperatures
discussed in calibration section) should only be made
under factory instruction . The list provided is for
reference only .
Temperature Controller Parameters
Description Units 1 Sensor Program 2 Sensor Program 3 Sensor Program
St1 Setpoint Value Sensor 1 Degrees 90 .0 90 .0 90 .0
St2 Setpoint Value Sensor 2 Degrees 3 .0 90 .0 90 .0
St3 Setpoint Value Sensor 3 Degrees 3 .0 3 .0 90 .0
r01 Differential Sensor 1 Degrees 10 .0 10 .0 10 .0
r02 Differential Sensor 2 Degrees 1 .0 10 .0 10 .0
r03 Differential Sensor 3 Degrees 1 .0 1 .0 10 .0
r4 Minimum Setpoint Value Degrees -50 .0 -50 .0 -50 .0
r5 Maximum Setpoint Value Degrees 150 .0 150 .0 150 .0
c01 Mode Sensor 1 Range dir dir dir
c02 Mode Sensor 2 Range inu dir dir
c03 Mode Sensor 3 Range inu inu dir
c11 Minimum Output 1 Stop Time Minutes 5 .0 5 .0 5 .0
c12 Minimum Output 2 Stop Time Minutes 0 .0 5 .0 5 .0
c13 Minimum Output 3 Stop time Minutes 0 .0 0 .0 5 .0
c21 Minimum Output 1 On Time Minutes 0 .0 0 .0 0 .0
c22 Minimum Output 2 On Time Minutes 0 .0 0 .0 0 .0
c23 Minimum Output 3 On Time Minutes 0 .0 0 .0 0 .0
c31 On Time Fault Sensor 1 Cycle Minutes 1 .0 1 .0 1 .0
c32 On Time Fault Sensor 2 Cycle Minutes 0 .0 1 .0 1 .0
c33 On Time Fault Sensor 3 Cycle Minutes 0 .0 0 .0 1 .0
c41 Off Time Fault Sensor 1 Cycle Minutes 0 .0 0 .0 0 .0
c42 Off Time Fault Sensor 2 Cycle Minutes 0 .0 0 .0 0 .0
c43 Off Time Fault Sensor 3 Cycle Minutes 0 .0 0 .0 0 .0
P0 Temp Scale Option F F F
P11 Sensor 1 Calibration Degrees 0 .0 0 .0 0 .0
P12 Sensor 2 Calibration Degrees 0 .0 0 .0 0 .0
P13 Sensor 3 Calibration Degrees 0 .0 0 .0 0 .0
P2 Decimal Point Option YES YES YES
P31 Sensor 1 Present Option YES YES YES
P32 Sensor 2 Present Option NO YES YES
P33 Sensor 3 Present Option NO NO YES
H2 Keypad Protection Option NO NO NO
H4 Serial Communications Address Range 0 0 0
H5 Keypad Code Range 0 0 0
H6 Type of Sensor Option Pt1 Pt1 Pt1
Shaded values are changed by the factory
2 . Press
OUT1 OUT2
°C
°F
Set Set
A
U
X
button to enter parameter list .
3 . With
OUT1 OUT2
°C
°F
Set Set
A
U
X
or
OUT1 OUT2
°C
°F
Set Set
A
U
X
button navigate to the desired
parameter on the list of parameters .
4 . Press
OUT1 OUT2
°C
°F
Set Set
A
U
X
button to see the current set value .
5 . Press either
OUT1 OUT2
°C
°F
Set Set
A
U
X
or
OUT1 OUT2
°C
°F
Set Set
A
U
X
button to set the desired new
value .
6 . Press
OUT1 OUT2
°C
°F
Set Set
A
U
X
button to confirm it and exit to the
parameter list .
7 . Press
OUT1 OUT2
°C
°F
Set Set
A
U
X
+
OUT1 OUT2
°C
°F
Set Set
A
U
X
buttons together to exit the
programming menu or wait 1 minute (keypad
timeout) .