3
2. You must assemble the model
according to the
instructions
. Do not alter or modify the model, as doing
so may result in an unsafe or unfl yable model. In a few
cases, the instructions may differ slightly from the photos.
In those instances, the written instructions should be
considered as correct.
3. You must take time to
build straight, true
and
strong
.
4. You must use an R/C radio system that is in good
condition, a correctly sized engine, and other components
as specifi ed in this instruction manual. All components
must be correctly installed so that the model operates
correctly on the ground and in the air. You must check
the operation of the model and all components before
every
fl ight.
5. If you are not an experienced pilot or have not fl own this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for
your fi rst fl ights. If you’re not a member of a club, your
local hobby shop has information about clubs in your
area whose membership includes experienced pilots.
6. While this ARF has been fl ight-tested to exceed normal use,
if the plane will be used for extremely high-stress fl ying, such
as racing, or if an engine larger than one in the recommended
range is used, the modeler is responsible for taking steps to
reinforce the high stress points and/or substituting hardware
more suitable for the increased stress.
7.
WARNING:
If you are powering this plane with an electric
motor, set the fail-safe on your transmitter so that the
motor is off if the signal is lost and follow the safety
precautions in the back of the manual.
We, as the ARF manufacturer, provide you with a top-quality,
thoroughly tested ARF and instructions, but ultimately
the quality and fl yability of your fi nished model depends
on how you assemble it; therefore, we cannot in any way
guarantee the performance of your completed model,
and no representations are expressed or implied as to the
performance or safety of your completed model.
REMEMBER:
Take your time and follow the instructions
to end up with a well-built model that is straight and true.
DECISIONS YOU MUST MAKE
This is a partial list of items required to fi nish the 55cc Big
Stik ARF that may require planning or decision-making
before starting to build. Order numbers are provided in
parentheses.
Gas Engine Recommendations
The recommended engine size range for the 55cc Big Stik
ARF is a 55 – 61cc [3.4 – 3.7 ci.] two-stroke gasoline engine.
We used the DLE-55RA, DLE-61 and O.S. GT60 engines.
Other engines can also be used, but you may need to make
modifi cations for mounting those engines.
❍
DLE-55RA (DLEG0455)
❍
DLE-61 (DLEG0061)
❍
O.S. GT60 (OSMG1560)
The stock muffl ers for DLE engines can be used.
The O.S. GT60 (OSMG1560) requires (4) 2" (51mm) standoffs
(OSMG8962) An aftermarket muffl er will also be required for
the O.S. GT60 engine.
ELECTRIC MOTOR
RECOMMENDATIONS
❍
Great Planes RimFire 65 [80-85-160] Outrunner Brushless
Motor (GPMG4805)
❍
Castle Creations Phoenix Edge 160HV 50V 160 Amp
ESC (CSEM0300)
❍
Male Star Plug (HCAM4010) (for the ESC)
❍
Series Battery Connector (GPMM3143)
❍
Two FlightPower LiPo FP50 5000mAh 22.2V Batteries
(FPWP5506)
❍
Great Planes Standoff Brushless Motor Mount XX Large
(GPMG1275)
❍
Propeller 24x12E
RADIO EQUIPMENT
The radio installation for the 55cc Big Stik ARF can be achieved
using three different radio set-ups: a basic Radio Set-up, an
Advanced Set-up and the S.Bus System Set-up.
Basic Radio Set-Up
The Basic Radio Set-up requires a 5-channel receiver. A
Y-harness is used to connect the two aileron servos together
and the two fl ap servos together. The Y-harnesses are then
plugged into the receiver. The rudder, elevator and throttle
are also plugged into the appropriate channels in the receiver.
❍
Futaba R617FS 7-Channel FASST Receiver (FUTL7627)
RECOMMENDED SERVOS:
All control surfaces require the
use of a high-quality servo of at least 100 oz-in of torque. A
servo of 40 oz-in of torque can be used for the throttle.
Function Servos
required
Elevator
❍
1 (min. 100 oz-in torque) (Futaba S9452
FUTM0662
)
OR
❍
Tactic TSX47 (
TACM0247
)
Rudder
❍
1 (min. 100 oz-in torque) (Futaba S9452
FUTM0662
)
OR
❍
Tactic TSX47 (
TACM0247
)
Ailerons
❍
2 (min. 100 oz-in torque) (Futaba S9452
FUTM0662
)
OR
❍
Tactic TSX47 (
TACM0247
)
