background image

WARRANTY

Great Planes Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship

at the date of purchase. This warranty does not cover any component parts damaged by use or modification. 

In no case

shall Great Planes’ liability exceed the original cost of the purchased kit.

Further, Great Planes reserves the right

to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be

assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the
act of using the user-assembled product, the user accepts all resulting liability.

If the buyers are not prepared to accept the liability associated with the use of this product, they are advised

to return this kit immediately in new and unused condition to the place of purchase.

READ THROUGH THIS INSTRUCTION MANUAL
FIRST. IT CONTAINS IMPORTANT INSTRUCTIONS
AND WARNINGS CONCERNING THE ASSEMBLY
AND USE OF THIS MODEL.

STTRP03  V1.1 for GPMA0001

Entire Contents © Copyright 2002

P.O. Box 788

Urbana, IL 61801

(217) 398-8970

[email protected]

INSTRUCTION MANUAL

TM

Wingspan

: 42 in

Wing Area

: 294 sq in

Airframe Weight

: 2.4 oz

Fuse Length

: 28-5/8 in

Wing Loading

: 4.41 - 6.37 oz/sq ft

Содержание BLT

























Отзывы: