GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 36

Страница: 36 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Active Hydraulic Systems

1. Lock hydraulic lever forward during field operation

for constant hydraulic flow to openers.

John Deere tractors with Sound-Gard® Body

Use lever lock clip, John Deere part number

R52667, to lock lever forward. See your tractor

dealer for clip purchase and installation.

John Deere 7000 Series tractors

: Rotate valve

detent selector to motor position to lock lever in for-

ward position.

John Deere 8000 Series tractors

: Set timer to con-

tinuous. Push lever forward until detent clicks.

Case-IH Magnum tractors

: Lock lever forward in

detent position. You may need to turn up detent

pressure to its maximum setting. Do not tie hydraulic

lever past detent position with a strap. See your trac-

tor dealer for hydraulic-system details.

Other tractors

: Lock lever forward in detent posi-

tion. You may need to turn up detent pressure to

maximum or use a mechanical detent holder to hold

lever forward. See your tractor dealer for proper

means of providing constant flow to openers.

Refer to Figure 25

2. With tractor hydraulic lever locked forward and

openers in field position, release lock disk and
set down-pressure with adjustment knob . Watch

pressure gauge and dial in desired pressure on

openers. There is one pressure-control valve for

openers on center section and one for openers on

wing sections of drill.

Note: Rotate knob clockwise to increase pressure and

counterclockwise to decrease pressure.

3. Once pressure is set, set knobs with lock disks .
4. In some applications, pressure on center section is

set slightly higher than the wings to account for

additional compaction from drill transport tires and

tractor tires. The recommended pressure range for

drilling is between 1200 psi and 1800 psi.

5. For more information on adjusting hydraulic down

pressure, see “

Row Unit Down Pressure

(Spring)

” on page 55.

Equipment Damage Risk:

During operation always raise openers before turning. Never
back up or turn sharply with openers in the ground. Doing so

will plug openers and may damage equipment.

Machine Damage Risk:

Tractors with load-sensing hydraulics must use the bypass
valve to operate the 3S-3000HD. Failure to use the bypass

valve can cause major tractor damage. Before adjusting

opener down pressure, set bypass valve per “

Setting the

Bypass Valve

” on page 20.

FigureSpacer

Population Risk:

Do not operate at pressures so high that

the gauge wheels loose traction, or are off the ground, result-
ing in skips and poor seed metering.

Figure 25 - Active

Pressure Control Valves

26477

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды