GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 32

Страница: 32 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Lowering Drill (Transport Lift)

Lowering from Transport Lift must be completed prior to

unfolding.
Transport Lift is on a dedicated hydraulic circuit. The

center main frame raises and lowers independently of

the opener sub-frames (which are raised and lowered by

the Opener Lift circuit).
The Transport Lift circuit also includes a cylinder for the

Transport Hooks, which lifts and restrains the

outer/forward ends of the wing sections when folded.
Transport Lift is normally used only when the drill is

folded. Opener Lift, and not Transport Lift, is used for

headland turns in field operations.

Transport Lower

1. Park tractor and drill on level ground with tractor

transmission in Park. Be aware of clearance needed

to unfold drill.

2. If the Two Outlet conversion kit is installed, confirm

that the selector valve, located near the hitch, is set

for Transport Lift operations. See “

Lift Selector

Valve Operation

” on page 43.

3. Slowly extended the Transport Lift circuit lever until

all three Transport Lift circuit cylinders are fully

extended (2 at transport wheels; 1 at transport hooks

on tongue). Set circuit lever to off or neutral (not

float).

Refer to Figure 21

4. Rotate cylinder lock channels down and forward off

transport lift cylinders.

FigureSpacer

Parking Stands Raised

(page 45) - Rotate stands up

and pin.

Walkboard Ladders Raised

- (if equipped)

Drill Raised and Locked

(page 25)

Make sure drill

is folded properly. Secure cylinder lock channels on
transport-cylinder rods and front box lift cylinders.
Allow transport lift cylinders to settle against lock
channels.

FigureSpacer

Figure 21

Transport Lift Cylinder Lock

18960

FigureSpacer

Figure 22

Front Box Lift Cylinder

Locked for Transport

15631

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды