GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 34

Страница: 34 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

If field operations are planned:

5. Position all six opener transport lock handles in

FIELD position.

6. Completely raise openers to allow opener transport

locks to disengage.

Note: The opener transport lock handles are spring load-

ed and can be moved to field position with openers

up or down, but locks will only disengage when

openers are completely raised. There are two lock

handles on each drill section.

Folding and Unfolding Quick Reference

To Fold Drill for Transport

• Fold markers (page 42).
• Raise openers (page 23).
• Fold drill (page 24).
• Raise drill (page 25).

To Unfold Drill for Field

• Lower drill (page 29).
• Unfold drill (page 29).
• Set openers for FIELD (page 23).

FigureSpacer

Figure 24 - Unfold

Opener Unlock

15549

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды