GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 46

Страница: 46 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Marker Operation

Optional markers are equipped with a double-selector

valve, on the tongue near the hitch, to combine the

box-fold circuit with the marker circuit. On a 2-outlet

tractor, there is a second selector valve, for the lift

circuits, mounted above the marker/fold selector.

Refer to Figure 38

After drill is unfolded for field operation, move

double-selector valve handle from forward fold position

to marker circuit (back ). Before operating markers,

make sure they are properly bled as described in

“

Bleeding Hydraulics

” on page 69.

Single Marker Operations

To operate a single marker, activate tractor remote

hydraulic lever to move marker in desired direction.
Single markers are equipped with a needle valve to

control marker folding speed. Excessive folding speed

can damage markers, so adjust needle valve to a safe

operating speed as described under “

Marker Speed

” on

page 62.

Dual Marker Operations

Dual markers are equipped with an automatic sequence

valve to control lift sequence. Starting with both markers

up, the sequence is:
• Activate hydraulic lever; right marker lowers while left

marker stays up.

• Reverse hydraulic lever; right marker raises while left

marker stays up.

• Activate hydraulic lever; left marker lowers while right

marker stays up.

• Reverse hydraulic lever; left marker raises while right

marker stays up.

Pattern repeats.
Folding speed of dual markers is adjusted with

adjustment screws on sequence-valve body. Excessive

folding speed can damage markers, so adjust markers to

a safe folding speed as described under “

Marker

Adjustments

” on page 59.

FigureSpacer

Figure 38

Fold / Marker Selector

15550

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды