GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 66

Страница: 66 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Marker Speed

The procedure for adjusting marker speed is different for

single marker with needle valve and dual markers with

sequence valve.

Single Marker/Needle Valve Speed

Refer to Figure 65

A needle valve controls the folding speed. The needle

valve is near the rod end of the marker cylinder.
With tractor idling at a normal operating speed, adjust

marker folding to a safe speed. Turn adjustment knob

clockwise to reduce folding speed or counterclockwise to

increase folding speed. Excessive folding speed could

damage markers and void the warranty.

FigureSpacer

Dual-Marker/Sequence Valve Speed

There is one adjustment screw for unfolding speed
and one for folding speed . You can identify adjustment

screws by markings stamped in valve body.

Turn adjustment screws clockwise ( : slower) to

decrease [un]folding speed and counterclockwise
( : faster) to increase [un]folding speed.
With tractor idling at a normal operating speed, adjust

marker folding to a safe speed. Excessive [un]folding

speed could damage markers and void the warranty.
After adjusting the folding speed, tighten jam nuts on hex

adjustment screws to hold settings.

End of Adjustments

FigureSpacer

Figure 65

Needle valve Adjustment

15625

FigureSpacer

Figure 66

Sequence Valve Adjustment

14048

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды