GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 74

Страница: 74 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Refer to Figure 72

1. Review warnings, bleeding notes and system infor-

mation on page 69.

2. With drill unfolded and fold cylinders completely

extended, disconnect rod end pins and swing the

cylinders so they will not contact anything when

extended.

3. Loosen rod end hose JIC fitting at elbow on right

fold cylinder.

4. Slowly supply oil to rod end of fold cylinders (line )

until oil appears at loosened hose fitting. Tighten fit-

ting and completely retract fold cylinders.

5. With cylinders completely retracted, loosen base end

hose JIC fitting at elbow on right fold cylinder.

6. Slowly supply oil to base end of fold cylinders (line

) until oil appears at loosened hose fitting. Tighten

base end hose fitting and cycle fold cylinders in and

out several times.

7. Re-pin cylinder rod clevis.

FigureSpacer

Figure 72

Bleeding Fold Hydraulics

15644

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды