GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 24

Страница: 24 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Setting the Bypass Valve

Refer to Figure 12

A bypass valve is plumbed into the opener down

pressure circuit. Tractors with load-sensing,

closed-center hydraulics require this bypass valve to

protect the tractor hydraulic system.
If you are unsure what type of hydraulic system is on

your tractor, contact your tractor manufacturer.

Turn the locking disc counter-clockwise to enable

adjustment.

Turn the adjustment knob counter-clockwise to

increase flow.

Turn the adjustment knob clockwise to decrease flow.

Turning it fully clockwise stops all bypass flow.

Tractors with Open Center Hydraulics

Release locking disc. Close bypass valve for no oil flow

by turning knob on valve clockwise completely. Tighten

locking disc. Always operate the drill with the bypass

valve locked closed.

Tractors with Pressure Compensating

Closed Center Hydraulics (PC Closed)

Release locking disc. Close bypass valve for no oil flow

by turning knob clockwise completely. Tighten locking

disc. Always operate the drill with the bypass valve

locked closed.

Tractors with Load Sensing Closed Center

Hydraulics (LS Closed) or Pressure Flow

Compensating (PFC) Systems

Machine Damage Risk

: Failure to use the bypass valve on

load-sensing tractors may cause major tractor damage.

1. Release locking disc. Initially close bypass valve for

no oil flow by turning knob on valve clockwise com-

pletely.

2. With tractor at half throttle, adjust flow-control valve

on tractor so openers raise and lower at a reason-

able speed. Keep tractor at one-half throttle for

remaining steps.

Note: The faster openers raise and lower, the greater po-

tential for oil heating, premature wear or tractor

damage.

3. Engage tractor hydraulics and lower openers. Lock

hydraulic lever on tractor for continuous operation.

See “

Raising and Lowering Openers

” on page 23.

FigureSpacer

Figure 12

Bypass Valve

19045

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды