GREAT PLAINS 1510HDP Скачать руководство пользователя страница 132

Страница: 132 / 135

Great Plains

| 118-949M | 2018-07-03

Table of Contents

Index

130

1525P and 1510HDP

Table of Contents

Index

slack, chain .......................................101
SMS 2.0 ....................................... 48

SMV (Slow Moving Vehicle) .................5
Sound-Gard® .....................................29
spacer washers ..................................82
specifications ....................................116
speed ............................................. 7

Speed Calibration ...............................44
speed sensor setup ..........................122
speed sensors ..................................110
speed, marker ........................... 22

123

splitter row ..........................................77
spreader .................................... 69

102

springs, down-pressure ......................69
springs, 25P .......................................74
SSToolbox ..........................................48
stagger, press wheel ................... 86

steering wheels ..................................20
storage .......................................... 3

straight blades ..................................113
sway blocks ........................................13
symbol, safety ......................................1

T handle ...................................... 71

tables

adjustments .................................52
cam, 25P .....................................74
coulter blade mount .....................80
document family ..........................10
hose color code ...........................14
marker extension .........................60
models covered ...........................10
specs, 1525P ............................116
specs,1510HDP ........................116
torque values .............................118
troubleshooting

population ............................88

UMC (Unit-Mount Coulter) ......... 79

113

UMC (unit-mount coulter) .................113

UMC (Unit-Mounted Coulter) ............. 69
UMC-RC (UMC row cleaner) ........... 113
UMC-RC (Unit-Mount Coulter RC) ..... 78
UMRC (Unit-Mount Row Cleaner) ...... 78
UM-RC (unit-mount row cleaner) ..... 113
unit-mounted

row cleaners ................................ 78

Unit-Mounted Coulter ......................... 69
unit-mounted coulter ........................ 113
unit-mounted coulters ......................... 73
unit-mounted row options ................. 113
units of measure ................................. 36
URLs, tires ....................................... 117

Varying Rates (Veris) ......................... 47
Veris ................................................... 26
Veris calibration .................................. 30
veris drive, MT .................................. 111
veris drive, no till .............................. 111
Veris prompts

CAL SETTINGS ENGLISH .. 36

CAL SETTINGS SPEED ............. 37
CAL SETTINGS WIDTH ............. 37
CAL SETTINGS # ROWS ........... 37
CALIBRATE ERROR .................. 40
CALIBRATION NUMBER .... 35

CLEAR DRIVE AREA .......... 39

DISTANCE ERROR .................... 46
ENGAGE AT 1ST FLAG ............. 45
ENGAGE AT 2ND FLAG ............ 46
ENGAGE RUN DRIVE ......... 39

ENGAGE TO STOP ............. 39

ENTER AMOUNT COLLECTED40

TIME TOO LOW/HIGH ............... 35
UP CALCULATE NEW ............... 47
UP CALIBRATE .......................... 45
UP KEEP NEW ........................... 44
VR spd out .................................. 29

Veris VR Mode ................................... 29
VER-21568, module ........................... 26
VR button ........................................... 28
VR (Variable Rate) ............................. 28

Содержание 1510HDP








































































































































Результаты поиска

Содержание 1510HDP

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510HDP, Руководство оператора

Результаты поиска

Содержание 1510HDP

Отзывы:

Бренды по названию

Популярные бренды