GREAT PLAINS 1510HDP Скачать руководство пользователя страница 70

Страница: 70 / 135

Great Plains

| 118-949M | 2018-07-03

Table of Contents

Index

1525P and 1510HDP

Table of Contents

Index

Adjustments

Refer to Figure 92

Engage the upper latch

. Make sure the tapered

line-up pins near drive sprocket engage completely
in line-up holes.

Refer to Figure 93

Engage the lower latch



To change from the Finger Pickup meter to the
Precision meter requires the same steps.

Refer to Figure 94

The meter drive can be disengaged if a meter is not
being used.

10. Disengage the drive coupler by pulling out on the

pin, twisting it a quarter turn and resting it in the
shallow slot.

A meter must always be assembled on an opener whether it is
being driven or not. Damage will occur if no meter is in place.

Disengaging drive coupler is not required to change
meters.

Figure 92

Engage Upper Latch

22870

Figure 93

Engage Lower Latch

22871

Figure 94

Disengage Meter Drive

22869

Содержание 1510HDP








































































































































Результаты поиска

Содержание 1510HDP

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510HDP, Руководство оператора

Результаты поиска

Содержание 1510HDP

Отзывы:

Бренды по названию

Популярные бренды