GREAT PLAINS 1510HDP Скачать руководство пользователя страница 116

Страница: 116 / 135

Great Plains

| 118-949M | 2018-07-03

Table of Contents

Index

112

1525P and 1510HDP

Table of Contents

Index

Options

Unit-Mounted Row Options

Row Cleaners

Optional Martin row cleaners are unit-mounted, either:

•

“stand-alone”, using a unit-mount assembly (

), or;

•

added to a UMC coulter disk mounting bracket (

with or without a disk).

Twin-Row drills and narrow row spacings support only
single-wheel unit-mounted row cleaners, in alternating
left/right cleaner hub orientations. Order one kit per row.

Unit-Mounted Disk Coulters

Optional unit-mount disk coulters (UMCs) are available
with 15 inch (38.1cm) fluted blades or 15 inch turbo
blades.

Check tractor clearance. Use of UMCs, particularly in
combination with row cleaners, may require a hitch
setback kit.

Order one kit per row.

Coulter Blades

Replacement and alternate coulter blades include (qty. 1
per row unit):

For operations, see:
“

Coulter Adjustments

” on page 78.

Single-Wheel, Stand-Alone

Part Number

SINGLE ARM RC ASM LH

207-092S

SINGLE ARM RC ASM RH

207-093S

Single-Wheel, Coulter-Mount

Part Number

LH ROW CLEANER UNIT

207-215K

RH ROW CLEANER UNIT

207-216K

25 Series 15 inch UM Coulters

Part Number

Coulter with Fluted Blade

202-616L

Coulter with Turbo Blade

202-617L

Blade

Part Number

Fluted, 15 inch (50 flutes)

820-331C

Turbo, 15 inch (20 flutes)

820-327C

Straight, 14 inch

820-259C

27308

29124

25299

Содержание 1510HDP








































































































































Результаты поиска

Содержание 1510HDP

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510HDP, Руководство оператора

Результаты поиска

Содержание 1510HDP

Отзывы:

Бренды по названию

Популярные бренды