manualshive.com logo in svg

GREAT PLAINS 1510HDP, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510HDP Скачать руководство пользователя страница 64

Great Plains

 | 118-949M | 2018-07-03

Table of Contents

Index

60

1525P and 1510HDP

Table of Contents

Index

Adjustments

Marker Extension

If markers were ordered as a separate accessory, or not
dealer-installed, mount them per the installation
instructions supplied with the markers.

Refer to Figure 79

Check the marker extension

. The installation

instructions may not cover setting the correct marker
length, or may specify a length not optimal for your row
configuration.

3-Point Drill drills have their row units spaced equally
about machine centerline. Set the initial marker
extension to the values specified in the diagrams on the
following pages, measured from the centerline of the
outside row (not the centerline of a pair) to the mark left
in the ground when the drill is lowered.

If you modify your row spacing by shutting off rows, this
can also change the marker extension required. Some
changes can result in an asymmetric row spacing about
machine centerline. This usually causes the marker
extension to be different for left and right sides,
depending on the direction of planting for each
successive pass.

Making short practice passes confirms correct marker extension.

Marker Extension Adjustment

Refer to Figure 80

To adjust a marker width or disk pivot orientation:

1.

Lower drill to field position and extend the marker
side to be adjusted.

2.

If disk angle or direction is to be changed, make that
change before adjusting extension.

3.

Pull forward to fully settle drill and leave a mark to
check.

4.

On telescoping outer marker tubes, loosen both jam
nuts

 and both 

1

2

 in set screws

.

5.

Move marker disk tube in or out to get the desired
mark placement. See diagrams starting on page 60
suggested initial marker extensions, measured from
outside row to mark.

6.

To change throw direction of marker, remove inner
tube completely, and reinsert at desired orientation.

7.

Tighten both 

1

2

 in set screws and then both jam

nuts.

8.

Pull forward to check actual results and fold marker.

Marker Extension Values

The diagrams in this section show marker extension
distances for all supported row unit configurations of all
drills covered by this manual.

Measure from the centerline of the outside row unit 

in

use

 on each side. Do not measure from a shut-off row

unit.

E

Figure 79

Marker Extension

E

Figure 80

Marker Extension Adjustment

19204

1

2

1

2

Содержание 1510HDP








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды