manualshive.com logo in svg

GREAT PLAINS 1510HDP, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510HDP Скачать руководство пользователя страница 24

Great Plains

 | 118-949M | 2018-07-03

Table of Contents

Index

20

1525P and 1510HDP

Table of Contents

Index

Operating Instructions

Transporting

For transporting with drill attached to a hitch, refer to your
hitch operator’s manual.

Check Tractor Capacity and Configuration

3-point implements can dangerously reduce weight on
tractor steering wheels.

•

Know the transport weight of your drill (see table on
previous page).

•

Consult your tractor manual for 3-point limitations.

•

Add weights to tractor as required.

When determining the weight of your drill, be sure to
include the weight of any seed loaded and row options.

Remove Extra Drill Weights

Remove weights from optional weight brackets. Move
weights to tractor as needed for ballasting.

Unload Seed Box

Unload seed box before transporting if at all possible.
See “

Material Clean-Out

” on page 93.

The drill can be transported with a full box of grain, but
the added weight will increase stopping distance and
decrease maneuverability.

To maintain steering control, you may need to add ballast
to your tractor front end. Refer to your tractor operator’s
manual for ballast required.

Secure Markers

Always transport markers in the folded position and
marker hydraulic circuit(s) in neutral (to prevent
unintended marker movement in cradles).

Transport Checklist

Plan the route. Avoid steep hills. Keep Clearances in 
mind.

Hitch: Make all electrical and hydraulic connections. 
See “

Hitching Tractor to Drill

” on page 13.

Refer to Figure 13

Fold up walkboard ladders for maximum clearance.

Fold markers. Lock circuit with Neutral setting.
See “

Marker Operation (Option)

” on page 22.

Raise drill.

Close all seed inlet shutters if transporting with seed.

Always have lights on for highway operation.

Comply with all federal, state and local safety laws 
when traveling on public roads.

Travel with caution. Allow safe clearance.
Remember that the drill is wider than the tractor.

Loss of Control Hazard:

Use a tractor rated for the load. Add tractor ballast as needed.
Do not exceed 20 mph. Towing the drill with a vehicle that is
not adequate, or at high speeds, could lead to loss of vehicle
control. Loss of vehicle can result in a serious road accident,
severe injury or death. Check that your tractor has enough to
handle the weight of the drill. Refer to your tractor’s operator
manual for capacities and ballast requirements.

Figure 13

Ladder Folded for Transport

18263

Содержание 1510HDP








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды