GRAUPNER Falcon 12 Скачать руководство пользователя

Страница: 7 / 52

7 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Intended use

These receivers should only be used for the purpose specified by the

manufacturer for operation of unmanned remote controlled mod-

els. This includes all types of UAVs or all types of unmanned aerial

vehicles as well as all types of unmanned land and water vehicles.

Any other type of use is impermissible and may cause significant

property damage and/or personal injury. No warranty or liability is

therefore offered for any improper use not covered by these provi-

sions.
In addition, it is explicitly pointed out that you must inform yourself

about the laws and regulations applicable at your respective starting

point before starting the remote control operation. Such conditions

may differ from state to state, but this must be followed in every

case.

Note

Read through this entire manual before you attempt to install or use

the receiver.

Target group

The item is not a toy. It is not suitable for children under 14. The

installation and operation of the receiver must be performed by

experienced modellers. If you do not have sufficient knowledge

about dealing with radio-controlled models, please contact an expe-

rienced modeler or a model club.

Package content

• Receiver of your choice
• Manual

Note

Graupner/SJ works continuously to the further development of the

products. We must therefore reserve the right to change the scope

of delivery in terms of form, technology and equipment.

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды